Dodge Stratus 2001-2006 Torque Specifications
Dodge Stratus 2001-2006

Dodge Stratus 2001-2006 Torque Specifications

Complete Dodge Stratus 2001-2006 torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.

Updated

Important Information

Safety guidelines and reference information for proper torque application

Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083

Common Torque Patterns

Star Pattern

Used for wheels and other circular bolt patterns

Star Pattern torque pattern diagram showing proper bolt tightening sequence
Cross Pattern

Used for gaskets and cover plates

Cross Pattern torque pattern diagram showing proper bolt tightening sequence
Sequential Pattern

Used for head bolts and other critical components

Sequential Pattern torque pattern diagram showing proper bolt tightening sequence

Common Mistakes to Avoid

Over-tightening

Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.

Prevention:

Always use a calibrated torque wrench and follow specifications exactly.

Incorrect Torque Sequence

Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.

Prevention:

Follow the manufacturer's specified torque sequence pattern.

Dirty Threads

Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.

Prevention:

Clean and inspect all threads before assembly. Use new thread locker if specified.

Reusing TTY Bolts

Torque-to-yield bolts are designed to stretch and must not be reused.

Prevention:

Always replace TTY bolts with new ones. They are single-use only.

Dry vs. Lubricated

Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.

Prevention:

Check if specs are for dry or lubricated threads. Use specified lubricant when required.

Recommended Tools

Torque Wrench (1/4" Drive)

Range: 2-25 ft-lbs
Small fasteners, delicate components

Torque Wrench (3/8" Drive)

Range: 10-100 ft-lbs
Most common automotive fasteners

Torque Wrench (1/2" Drive)

Range: 30-250 ft-lbs
Large fasteners, wheels

Angle Gauge

Torque-to-yield (TTY) bolts

Torque Wrench Care

  • Calibrate annually or after 5,000 clicks
  • Store at lowest setting
  • Keep clean and lubricated

Search Specifications

Search by component name, bolt size, or description

Torque Calculator

Convert between different torque units

2.4l Engine

Torque specifications for 2.4L Engine

Cylinder Head

1

Cylinder Head Bolts

M10 x 1.25
Torque Specification
1. 25 ft-lbs (34 N·m) 2. 90°
Important Notes
Follow the manufacturer's specified torque sequence for the cylinder head bolts. Failure to do so may result in head gasket failure.
2

Rocker Arms/Shafts Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure the rocker arms are properly seated before tightening.

Crankshaft And Bearings

1

Main Bearing Bolts

M12 x 1.5
Torque Specification
100 ft-lbs (135 N·m)
Important Notes
Follow the manufacturer's specified torque sequence for the main bearing bolts.
2

Connecting Rod Nuts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure the connecting rods are properly seated on the crankshaft journals.

Timing System

1

Camshaft Sprocket Bolt

M10 x 1.25
Torque Specification
75 ft-lbs (102 N·m)
Important Notes
Ensure the camshaft sprocket is properly aligned with the timing marks.
2

Timing Belt/Chain Tensioner Bolt

M8 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure the tensioner is properly adjusted before tightening.

Oil System

1

Oil Pan Bolts

M6 x 1.0
Torque Specification
8.3 ft-lbs (11 N·m)
Important Notes
Follow the manufacturer's specified torque sequence for the oil pan bolts.
2

Oil Drain Plug Bolt

M14 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Replace the crush washer if necessary.

Exhaust System

1

Exhaust Manifold/Headers Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Follow the manufacturer's specified torque sequence for the exhaust manifold bolts.

2.7l Engine

Torque specifications for 2.7L Engine

Cylinder Head

1

Cylinder Head Bolts

M10 x 1.5
Torque Specification
1. 25 ft-lbs (34 N·m) 2. 90°
Important Notes
Follow the manufacturer's specified torque sequence to ensure even clamping force.
2

Rocker Arms/Shafts Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure rocker arms are properly seated before tightening.

Crankshaft And Bearings

1

Main Bearing Bolts

M12 x 1.75
Torque Specification
100 ft-lbs (135 N·m)
Important Notes
Follow the manufacturer's specified torque sequence to ensure even clamping force.
2

Connecting Rod Nuts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure connecting rods are properly seated on the crankshaft journals.
3

Flywheel Bolts

M10 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Use thread locker on flywheel bolts as specified by the manufacturer.

Timing System

1

Timing Belt/Chain Tensioner Bolt

M8 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure the tensioner is properly aligned before tightening.
2

Camshaft Sprocket Bolt

M12 x 1.75
Torque Specification
75 ft-lbs (102 N·m)
Important Notes
Use thread locker on the bolt as specified by the manufacturer.

Lubrication System

1

Oil Pan Bolts

M6 x 1.0
Torque Specification
8.3 ft-lbs (11 N·m)
Important Notes
Ensure the oil pan gasket is properly seated before tightening.
2

Oil Pump Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure the oil pump is properly aligned before tightening.

Cooling System

1

Water Pump Bolts

M6 x 1.0
Torque Specification
8.3 ft-lbs (11 N·m)
Important Notes
Ensure the water pump gasket is properly seated before tightening.
2

Thermostat Housing Bolts

M6 x 1.0
Torque Specification
8.3 ft-lbs (11 N·m)
Important Notes
Ensure the thermostat housing gasket is properly seated before tightening.

3.0l Engine

Torque specifications for 3.0L Engine

Cylinder Head

1

Cylinder Head Bolts

M10 x 1.5
Torque Specification
1. 25 ft-lbs (34 N·m) 2. 90°
Important Notes
Follow the manufacturer's specified torque sequence for proper sealing.
2

Rocker Arms/Shafts Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure proper valve operation by tightening evenly.
3

Valve Cover Bolts

M6 x 1.0
Torque Specification
7.08 ft-lbs (10 N·m)
Important Notes
Use a crisscross pattern to ensure even sealing.

Crankshaft And Bearings

1

Main Bearing Bolts

M12 x 1.75
Torque Specification
100 ft-lbs (135 N·m)
Important Notes
Follow the manufacturer's specified torque sequence for proper alignment.
2

Connecting Rod Nuts

M10 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure proper piston movement by tightening evenly.
3

Flywheel Bolts

M12 x 1.75
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Ensure proper torque transfer and engine balance.

Timing System

1

Timing Belt/Chain Tensioner Bolt

M8 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure proper timing belt/chain tension.
2

Camshaft Sprocket Bolt

M10 x 1.5
Torque Specification
75 ft-lbs (102 N·m)
Important Notes
Ensure proper camshaft timing.
3

Crankshaft Pulley/Harmonic Balancer Bolt

M12 x 1.75
Torque Specification
105 ft-lbs (142 N·m)
Important Notes
Ensure proper engine balance and accessory drive operation.

Intake And Exhaust

1

Intake Manifold Bolts

M8 x 1.25
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Follow the manufacturer's specified torque sequence to prevent vacuum leaks.
2

Exhaust Manifold/Headers Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Follow the manufacturer's specified torque sequence to prevent exhaust leaks.

Lubrication System

1

Oil Pan Bolts

M6 x 1.0
Torque Specification
8.33 ft-lbs (11 N·m)
Important Notes
Follow the manufacturer's specified torque sequence to prevent oil leaks.
2

Oil Pump Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure proper oil pressure and lubrication.
3

Oil Filter Housing Bolt

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure proper oil filtration and prevent leaks.
4

Oil Drain Plug Bolt

M12 x 1.75
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Prevent oil leaks by tightening to the specified torque.

Cooling System

1

Water Pump Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure proper coolant circulation and prevent leaks.
2

Thermostat Housing Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure proper coolant flow and prevent leaks.

Accessory Drives

1

Starter Motor Mounting Bolts

M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure proper engagement with the flywheel.
2

Alternator Mounting Bolts

M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure proper charging system operation.
3

A/C Compressor Mounting Bolts

M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure proper operation of the A/C system.
4

Power Steering Pump Mounting Bolts

M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure proper power steering operation.

Ignition System

1

Spark Plugs

M14 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure proper sealing and prevent compression loss.

Sensors

1

Crankshaft Position Sensor Bolt

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure accurate engine timing signals.
2

Camshaft Position Sensor Bolt

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure accurate valve timing signals.
3

Knock Sensor Bolt

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure proper detection of engine knock for optimal performance.

Timing Cover

1

Timing Cover Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Follow the manufacturer's specified torque sequence to ensure proper sealing.

41te Transmission

Torque specifications for 41te Transmission

Transmission Mounting

1

Transmission Mounting Bolts

M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the transmission is properly aligned before torquing.

Oil Pan

1

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
8.3 ft-lbs (11 N·m)
Important Notes
Use a crisscross pattern to ensure even sealing.

Fluid Plugs

1

Transmission Drain Plug

M12 x 1.75
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Replace the crush washer if applicable.
2

Transmission Fill Plug

M12 x 1.75
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the plug is properly seated to prevent leaks.

Drive Axle

1

Drive Axle/Half Shaft Bolts

M12 x 1.5
Torque Specification
80 ft-lbs (108 N·m)
Important Notes
Ensure the axle is fully seated before torquing.
2

CV Joint/Axle Nut

M24 x 1.5
Torque Specification
180 ft-lbs (244 N·m)
Important Notes
Use a torque wrench with a high-capacity range.

Starter Motor

1

Starter Motor Mounting Bolts

M8 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the starter motor is properly aligned before torquing.

Torque Converter

1

Torque Converter Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure the torque converter is fully seated before torquing.

Valve Body

1

Valve Body Bolts

M6 x 1.0
Torque Specification
8.3 ft-lbs (11 N·m)
Important Notes
Use a crisscross pattern to ensure even torque distribution.

Transmission Case

1

Transmission Case Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure the case halves are properly aligned before torquing.

Shift Linkage

1

Shift Linkage Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure the linkage is properly aligned before torquing.

Cooler Lines

1

Transmission Cooler Line Fittings

M12 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure the fittings are properly seated before torquing.

Body

Torque specifications for Body

Suspension

1

Strut/Shock Absorber Mounting Bolts

M12 x 1.5
Torque Specification
80 ft-lbs (108 N·m)
Important Notes
Ensure proper alignment of the suspension system during installation.

Fuel System

1

Fuel Tank Strap Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure the fuel tank is properly aligned before tightening.
2

Fuel Filler Neck Bolts

M6 x 1.0
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure a tight seal to prevent fuel vapor leaks.

Electrical

1

Battery Terminal Nuts

M6 x 1.0
Torque Specification
4.2 ft-lbs (5.5 N·m)
Important Notes
Ensure a clean and corrosion-free connection.

Body Panels

1

Body Panel Bolts

M6 x 1.0
Torque Specification
12.5 ft-lbs (17 N·m)
Important Notes
Estimated value based on typical body panel bolt sizes. Avoid over-tightening to prevent panel damage.

Safety

1

Seat Belt Anchor Bolts

M10 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Critical for occupant safety. Ensure proper torque to withstand impact forces.

Exterior

1

Bumper Mounting Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure proper alignment of the bumper during installation.
2

Roof Rack Mounting Bolts

M6 x 1.0
Torque Specification
17.5 ft-lbs (24 N·m)
Important Notes
Estimated value based on typical roof rack bolt sizes. Ensure secure attachment to prevent loosening.
3

Spoiler or Wing Mounting Bolts

M6 x 1.0
Torque Specification
17.5 ft-lbs (24 N·m)
Important Notes
Estimated value based on typical spoiler bolt sizes. Ensure proper alignment and secure attachment.

Doors

1

Door Hinge Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure proper door alignment during installation.

Brakes

Torque specifications for Brakes

Brake Caliper System

1

Brake Caliper Bolts

M10 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
These bolts secure the brake caliper to the mounting bracket. Ensure proper alignment before torquing.
2

Brake Caliper Mounting Bracket Bolts

M12 x 1.5
Torque Specification
80 ft-lbs (108 N·m)
Important Notes
These bolts attach the caliper mounting bracket to the steering knuckle or axle. Ensure the bracket is properly seated before torquing.

Brake Rotor Drum System

1

Brake Disc/Drum Retaining Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
These bolts hold the brake rotor or drum to the wheel hub. Ensure the rotor/drum is properly seated before torquing.

Brake Hydraulic System

1

Brake Hose Banjo Bolt

M10 x 1.0
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
This bolt connects the brake hose to the caliper. Ensure the sealing washers are properly installed before torquing.
2

Brake Master Cylinder Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value. These bolts secure the master cylinder to the brake booster. Ensure proper alignment before torquing.

Brake Booster Pedal System

1

Brake Booster Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value. These bolts attach the brake booster to the firewall. Ensure proper alignment before torquing.
2

Brake Pedal Assembly Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value. These bolts secure the brake pedal assembly to the firewall or pedal bracket. Ensure proper alignment before torquing.

Abs System

1

ABS Sensor Mounting Bolts

M6 x 1.0
Torque Specification
12 ft-lbs (16 N·m)
Important Notes
Estimated value. These bolts secure the ABS wheel speed sensor to the steering knuckle or axle. Ensure proper alignment before torquing.

Wheel Attachment System

1

Wheel Lug Nuts

M12 x 1.5
Torque Specification
100 ft-lbs (135 N·m)
Important Notes
These nuts secure the wheel to the hub. Use a star pattern when tightening to ensure even pressure.

Drivetrain

Torque specifications for Drivetrain

Engine To Transmission

1

Flywheel Bolts

M10 x 1.25
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Critical for transferring engine power to the transmission. Ensure proper torque to prevent flywheel detachment.
2

Torque Converter Bolts

M8 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Estimated value based on similar bolt sizes. Ensures secure attachment of the torque converter to the flexplate.
3

Transmission Bellhousing Bolts

M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensures proper alignment of the transmission with the engine block.

Transmission

1

Transmission Mounting Bolts

M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensures the transmission remains stable and aligned with the chassis.
2

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
8.3 ft-lbs (11 N·m)
Important Notes
Prevents leaks and ensures the oil pan remains securely attached.
3

Transmission Drain Plug

M12 x 1.75
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Prevents leaks and ensures the drain plug remains securely in place.
4

Transmission Fill Plug

M12 x 1.75
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Prevents leaks and ensures the fill plug remains securely in place.

Driveshaft And Axles

1

Drive Axle/Half Shaft Bolts

M12 x 1.5
Torque Specification
80 ft-lbs (108 N·m)
Important Notes
Ensures the axles remain securely attached to the transmission or differential.
2

CV Joint/Axle Nut

M24 x 1.5
Torque Specification
180 ft-lbs (244 N·m)
Important Notes
Ensures the CV joint remains securely attached to the wheel hub.
3

Propeller/Drive Shaft Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensures the drive shaft remains securely attached to the transmission or differential.

Differential And Transfer Case

1

Differential Mounting Bolts

M12 x 1.5
Torque Specification
80 ft-lbs (108 N·m)
Important Notes
Ensures the differential remains stable and aligned with the chassis.
2

Differential Drain Plug

M12 x 1.75
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Prevents leaks and ensures the drain plug remains securely in place.
3

Differential Fill Plug

M12 x 1.75
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Prevents leaks and ensures the fill plug remains securely in place.
4

Transfer Case Mounting Bolts

M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensures the transfer case remains stable and aligned with the chassis.
5

Transfer Case Drain Plug

M12 x 1.75
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Prevents leaks and ensures the drain plug remains securely in place.
6

Transfer Case Fill Plug

M12 x 1.75
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Prevents leaks and ensures the fill plug remains securely in place.

Electrical

Torque specifications for Electrical

Ignition System

1

Ignition Coil Bolt

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure the ignition coil is seated properly before tightening.

Starting System

1

Starter Motor Mounting Bolts

M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the starter motor is properly aligned with the flywheel.

Charging System

1

Alternator Mounting Bolts

M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Check belt tension after tightening the alternator bolts.

Battery System

1

Battery Terminal Nuts

M6 x 1.0
Torque Specification
4.17 ft-lbs (5.5 N·m)
Important Notes
Ensure terminals are clean and free of corrosion before tightening.

Grounding System

1

Ground Strap Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (13.5 N·m)
Important Notes
Estimated value based on similar grounding components.

Engine Control System

1

ECU/ECM Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Estimated value based on similar electronic control units.
2

Crankshaft Position Sensor Bolt

M6 x 1.0
Torque Specification
10 ft-lbs (13.5 N·m)
Important Notes
Ensure the sensor is properly aligned before tightening.

Electrical Accessories

1

A/C Compressor Mounting Bolts

M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the compressor is properly aligned with the drive belt.
2

Fuse Box Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Estimated value based on similar fuse box components.
3

Wiring Harness Clamp Bolts

M6 x 1.0
Torque Specification
5 ft-lbs (6.8 N·m)
Important Notes
Ensure the wiring harness is properly routed before tightening.

Emissions Sensors

Torque specifications for Emissions_sensors

Egr System

1

EGR Valve Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure the EGR valve gasket is properly seated before tightening.
2

EGR Tube Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Estimated value based on similar EGR system components.

Exhaust Manifold

1

Exhaust Manifold/Headers Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Use a crisscross pattern to ensure even sealing.
2

Exhaust Manifold/Headers to Cylinder Head Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure the manifold is properly aligned before tightening.

Exhaust Pipe

1

Exhaust Pipe to Exhaust Manifold/Headers Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure the exhaust pipe is properly aligned before tightening.
2

Catalytic Converter to Exhaust Pipe Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure the catalytic converter is properly aligned before tightening.

Oxygen Sensor

1

Oxygen (O2) Sensor

M18 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Estimated value based on typical O2 sensor torque specifications.

Secondary Air Injection

1

Secondary Air Injection System Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Estimated value based on similar emissions system components.

Exhaust

Torque specifications for Exhaust

Exhaust Manifold

1

Exhaust Manifold/Headers to Cylinder Head Bolts

M10 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to evenly distribute pressure and prevent leaks.

Exhaust Pipe Connections

1

Exhaust Pipe to Exhaust Manifold/Headers Bolts

M10 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure gaskets are properly seated before tightening.
2

Catalytic Converter to Exhaust Pipe Bolts

M10 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure gaskets are in good condition and properly seated.
3

Muffler to Exhaust Pipe Bolts

M10 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure proper alignment to avoid stress on the exhaust system.

Exhaust Support

1

Exhaust Hanger Bolts/Brackets

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Estimated value based on similar components. Ensure hangers are properly aligned to avoid stress on the exhaust system.

Oxygen Sensor

1

Oxygen Sensor (O2 Sensor)

M18 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure the sensor is properly seated and aligned before tightening.

Heat Shield

1

Heat Shield Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure heat shields are properly aligned to avoid rattling or loosening over time.

Exhaust Flange

1

Exhaust Flange Bolts

M10 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure gaskets are in good condition and properly seated.

Fuel

Torque specifications for Fuel

Fuel Delivery System

1

Fuel Rail Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensures a leak-free connection and maintains fuel pressure.
2

Fuel Injector Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Prevents fuel leaks and ensures proper injector seating.
3

Fuel Pump Mounting Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensures the pump is securely mounted, preventing leaks.

Fuel Tank System

1

Fuel Tank Strap Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensures the tank is securely mounted, preventing movement.
2

Fuel Filler Neck Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensures a tight seal, preventing fuel leaks.
3

Fuel Tank Sender Unit Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensures a proper seal and prevents fuel leaks.

Fuel Filtration System

1

Fuel Filter Bolt/Nut

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensures a leak-free connection and maintains fuel flow integrity.

Fuel Emissions System

1

Fuel Vapor Canister Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensures the canister is securely mounted, preventing leaks.

Hvac

Torque specifications for Hvac

Ac Compressor

1

A/C Compressor Mounting Bolts

M10 x 1.5
Torque Specification
40 ft-lbs (54 N-m)
Important Notes
Ensure bolts are tightened in a cross pattern to evenly distribute load. Estimated bolt size based on typical A/C compressor applications.

Refrigerant Lines

1

A/C Line Fittings

M8 x 1.25
Torque Specification
25 ft-lbs (34 N-m)
Important Notes
Ensure fittings are clean and free of debris before tightening. Estimated bolt size based on typical refrigerant line applications.
2

Expansion Valve or Orifice Tube Fittings

M8 x 1.25
Torque Specification
25 ft-lbs (34 N-m)
Important Notes
Ensure fittings are properly aligned to avoid damage to the expansion valve or orifice tube. Estimated bolt size based on typical applications.

Condenser

1

Condenser Mounting Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N-m)
Important Notes
Ensure bolts are tightened in a cross pattern to evenly distribute load. Estimated bolt size based on typical condenser applications.

Evaporator And Heater Core

1

Evaporator Core Housing Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N-m)
Important Notes
Ensure bolts are tightened in a cross pattern to evenly distribute load. Estimated bolt size based on typical housing applications.
2

Heater Core Housing Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N-m)
Important Notes
Ensure bolts are tightened in a cross pattern to evenly distribute load. Estimated bolt size based on typical housing applications.

Blower Motor

1

Blower Motor Mounting Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N-m)
Important Notes
Ensure bolts are tightened in a cross pattern to evenly distribute load. Estimated bolt size based on typical blower motor applications.

Control Panel

1

HVAC Control Panel Mounting Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N-m)
Important Notes
Ensure bolts are tightened in a cross pattern to evenly distribute load. Estimated bolt size based on typical control panel applications.

Suspension

Torque specifications for Suspension

Strut Shock Absorber

1

Strut/Shock Absorber Mounting Bolts

M12 x 1.5
Torque Specification
80 ft-lbs (108 N·m)
Important Notes
Ensure bolts are tightened evenly to prevent misalignment.
2

Upper Strut Mount Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Estimated value based on typical upper strut mount bolt sizes.

Control Arm System

1

Control Arm Bolts

M14 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Follow the manufacturer's torque sequence for proper alignment.
2

Ball Joint Nut

M12 x 1.25
Torque Specification
75 ft-lbs (102 N·m)
Important Notes
Ensure the ball joint is properly seated before tightening.
3

Lower Control Arm Bracket Bolts

M14 x 1.5
Torque Specification
90 ft-lbs (122 N·m)
Important Notes
Estimated value based on typical control arm bracket bolt sizes.

Steering System

1

Tie Rod End Nut

M10 x 1.25
Torque Specification
55 ft-lbs (75 N·m)
Important Notes
Ensure the tie rod end is properly seated before tightening.
2

Steering Knuckle Bolts

M12 x 1.5
Torque Specification
100 ft-lbs (135 N·m)
Important Notes
Estimated value based on typical steering knuckle bolt sizes.

Sway Bar System

1

Sway Bar Link Nut

M8 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the sway bar link is properly seated before tightening.

Drivetrain System

1

Drive Axle/Half Shaft Bolts

M12 x 1.5
Torque Specification
80 ft-lbs (108 N·m)
Important Notes
Ensure the drive axle is properly seated before tightening.
2

CV Joint/Axle Nut

M24 x 1.5
Torque Specification
180 ft-lbs (244 N·m)
Important Notes
Ensure the CV joint is properly seated before tightening.

Rear Suspension System

1

Rear Trailing Arm Bolts

M14 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Estimated value based on typical trailing arm bolt sizes.

Subframe System

1

Subframe Bolts

M16 x 1.5
Torque Specification
120 ft-lbs (163 N·m)
Important Notes
Estimated value based on typical subframe bolt sizes.

Troubleshooting Guide

Common issues, diagnostic steps, and prevention guidelines

Common Issues

Bolt stretching, stripped threads, uneven torque patterns

Loose Components

Symptoms:
  • Rattling or vibration noises
  • Visible movement in components
  • Uneven panel gaps
Solutions:
  • Clean threads and mounting surfaces
  • Replace damaged fasteners
  • Apply proper torque in sequence
  • Use thread locker if specified

Stripped Fasteners

Symptoms:
  • Unable to achieve proper torque
  • Fastener spins freely
  • Visible thread damage
Solutions:
  • Use thread repair kit if appropriate
  • Install thread insert (HeliCoil)
  • Replace component if threaded hole is damaged
  • Upgrade to higher grade fastener if recommended

Overtightened Components

Symptoms:
  • Cracked or deformed parts
  • Broken fasteners
  • Compressed gaskets or seals
Solutions:
  • Replace damaged components
  • Use new fasteners
  • Follow proper torque sequence
  • Verify correct torque specifications

Diagnostic Steps

Visual inspection, torque verification, thread assessment

1

Visual Inspection

Inspect the affected area for any visible signs of damage or wear

  • Check for cracks or deformation
  • Look for signs of excessive wear
  • Verify proper fastener installation
2

Torque Verification

Verify the torque applied to the fasteners

  • Check the torque wrench calibration
  • Verify the torque specification
  • Compare the applied torque to the specification
3

Thread Assessment

Assess the condition of the threads

  • Check for signs of thread damage
  • Verify the thread type and size
  • Check for proper thread engagement

Prevention Guidelines

Best practices, maintenance tips, tool care

Best Practices

  • Always follow the recommended torque specification
  • Use the correct type and size of fasteners
  • Verify the torque wrench calibration regularly

Maintenance Tips

  • Regularly inspect the affected area for signs of wear or damage
  • Replace damaged or worn-out components promptly
  • Keep the work area clean and organized

Tool Care

  • Regularly clean and maintain the torque wrench
  • Store the torque wrench in a dry and secure location
  • Verify the torque wrench calibration before each use

Frequently Asked Questions

Find answers to common questions about torque specifications

Q1

What are the general tightening guidelines for Dodge Stratus 2001-2006 bolts?

Always follow the recommended torque specifications provided in the vehicle service manual. Use a calibrated torque wrench to ensure accurate tightening. Apply anti-seize lubricant to threads where necessary unless otherwise stated. Refer to your service manual for specific torque values and tightening sequence.

Q2

How do I convert torque values between different units (e.g., Nm to ft-lb)?

To convert torque values, use the following formula: 1 Nm = 0.73756 ft-lb. For example, to convert 100 Nm to ft-lb, multiply 100 by 0.73756, which equals 73.756 ft-lb.

Q3

What are the common torque mistakes to avoid?

Common torque mistakes include over-tightening, under-tightening, using incorrect torque values, cross-threading, and stripping threads. Always consult your service manual for specific torque specifications and follow proper tightening procedures.

Q4

What are the consequences of improper torque application?

Improper torque application can lead to various issues, including bolt failure, component damage, leaks, and reduced vehicle safety. It IS crucial to follow the specified torque values and use the correct tools to avoid these potential problems.

Q5

How do I ensure the accuracy of my torque wrench?

To ensure the accuracy of your torque wrench, have it calibrated periodically by an accredited calibration facility. Regularly check the wrench's calibration status to maintain its precision and accuracy.

Q6

Where can I find additional torque-related information and resources?

Refer to the Dodge technical service manual for detailed torque specifications and tightening procedures. You can also consult automotive repair books, online forums, and reputable automotive websites for additional information.

Environmental Considerations

Temperature, humidity, and seasonal effects on torque specifications

Temperature Effects

Includes: High Heat, Cold Weather, Thermal Cycling

Temperature can significantly impact torque values and fastener behavior

Cold Weather

Effects:
  • Increased material brittleness
  • Higher torque required due to thread contraction
  • Reduced thread lubricant effectiveness
Recommendations:
  • Allow components to warm to room temperature when possible
  • Consider using winter-grade thread lubricants
  • Check torque values more frequently during winter months

Hot Weather

Effects:
  • Thermal expansion of components
  • Decreased friction in threads
  • Accelerated lubricant breakdown
Recommendations:
  • Check torque when components are at normal operating temperature
  • Use temperature-resistant thread lockers
  • Consider re-torquing after heat cycles

Humidity and Corrosion

Covers: Rust Prevention, Salt Exposure, Moisture Control

Moisture and corrosion can affect fastener integrity and torque values

High Humidity

Effects:
  • Accelerated corrosion formation
  • Reduced friction coefficient
  • Potential thread seizing
Prevention:
  • Use corrosion-resistant fasteners
  • Apply appropriate anti-seize compounds
  • Maintain proper protective coatings

Salt Exposure

Effects:
  • Rapid corrosion development
  • Thread damage
  • Seized fasteners
Prevention:
  • Regular underbody washing
  • Use of sacrificial anodes where appropriate
  • Application of protective coatings

Seasonal Maintenance

Spring, Summer, Fall, and Winter maintenance schedules

Spring

  • Inspect for winter damage
  • Clean and protect exposed fasteners
  • Check torque on critical components

Summer

  • Monitor heat-affected components
  • Check expansion-related loosening
  • Inspect cooling system mounts

Fall

  • Prepare for winter conditions
  • Apply corrosion protection
  • Verify all fasteners are properly torqued

Winter

  • More frequent inspection of critical fasteners
  • Check for salt damage
  • Monitor suspension component torque

Related Resources

Tools, service procedures, and technical bulletins

Recommended Tools

Digital Torque Wrench (10-100 Nm)

Essential for tightening fasteners to precise torque specifications, preventing damage and ensuring proper assembly. This range IS suitable for many applications on the stratus.

  • Digital display for accurate readings
  • Audible alarm when target torque IS reached
  • Multiple units (Nm, ft-lb, in-lb)
  • Reversible ratcheting mechanism
Learn more
Service Procedures

Bolt Tightening Sequence and Torque Specifications for Dodge stratus 2001-2006

Technical procedure overview specific to Dodge stratus

  • 1. Clean all threads and bolt surfaces.
  • 2. Apply a small amount of thread locker to the bolts.
  • 3. Tighten the bolts in the correct sequence to the specified torque.
  • 4. Use a torque wrench to ensure the bolts are tightened to the correct torque.
  • 5. Double-check all bolts to ensure they are properly tightened.
  • **Safety considerations and warnings:**
  • 1. Always wear safety glasses and gloves when working on your vehicle.
  • 2. Do not overtighten the bolts.
  • 3. Use the correct size and type of wrench for the bolts.
  • 4. Do not attempt to loosen or remove bolts that are rusted or damaged.
  • **Specific instructions for this component:**
  • 1. The cylinder head bolts must be tightened in the correct sequence to 90 ft-lb.
  • 2. The intake manifold bolts must be tightened in the correct sequence to 10 ft-lb.
  • 3. The exhaust manifold bolts must be tightened in the correct sequence to 15 ft-lb.
  • 4. The crankshaft pulley bolt must be tightened to 200 ft-lb.
  • 5. The timing belt tensioner bolt must be tightened to 30 ft-lb.
View full procedure
Technical Service Bulletins

Cylinder Head Bolt Torque Specifications

2003-04-15

Detailed bulletin description for Dodge stratus

2001-2006 stratus

Resolution: Complete resolution steps with torque specifications

Legal Disclaimer

Important information about using this content

Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.

General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability

The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.

We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.

Technical Information
  • All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
  • Vehicle specifications and procedures may vary by model year, trim level, and region.
  • Always follow the manufacturer's recommended procedures and safety precautions.
  • Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
  • If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.

About the Author

Expert automotive knowledge and experience

Alan Montanye - Automotive Technical Specialist
ASE

Alan Montanye

Automotive Technical Specialist

ASE Master Certified Technician with over a decade of hands-on experience in automotive repair and diagnostics.

Facebook Contact
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions

Diagnostic

Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.

Repair

Expert in both traditional mechanical repairs and modern vehicle systems.

Additional Expertise

Documentation

Created over 500 detailed repair guides and technical documents.

Training

Conducted technical training sessions and contributed to repair databases.

Certifications & Research

Certifications

  • ASE Master Technician Certification
  • Advanced Diagnostic Specialist
  • Hybrid/Electric Vehicle Systems
  • Performance Tuning Expert

Research & Community

Actively researches emerging technologies and contributes to automotive forums.

© 2025 Dodge Specs. All rights reserved.

Privacy Policy Terms of Service