Dodge Dakota 1997-2004
Dodge Dakota 1997-2004 Torque Specifications
Complete Dodge Dakota 1997-2004 torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.
Updated
Important Information
Safety guidelines and reference information for proper torque application
Safety First
- Always verify torque specifications with your vehicle's factory service manual
- Use properly calibrated torque wrenches
- Replace all torque-to-yield (TTY) bolts - they are single-use only
- When in doubt, consult a professional mechanic
Quick Reference Guide
Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083
Common Torque Patterns
Star Pattern
Used for wheels and other circular bolt patterns
Cross Pattern
Used for gaskets and cover plates
Sequential Pattern
Used for head bolts and other critical components
Common Mistakes to Avoid
Common Mistakes to Avoid
Over-tightening
Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.
Prevention:
Always use a calibrated torque wrench and follow specifications exactly.
Incorrect Torque Sequence
Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.
Prevention:
Follow the manufacturer's specified torque sequence pattern.
Dirty Threads
Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.
Prevention:
Clean and inspect all threads before assembly. Use new thread locker if specified.
Reusing TTY Bolts
Torque-to-yield bolts are designed to stretch and must not be reused.
Prevention:
Always replace TTY bolts with new ones. They are single-use only.
Dry vs. Lubricated
Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.
Prevention:
Check if specs are for dry or lubricated threads. Use specified lubricant when required.
Recommended Tools
Recommended Tools
Torque Wrench (1/4" Drive)
Range: 2-25 ft-lbs
Small fasteners, delicate components
Torque Wrench (3/8" Drive)
Range: 10-100 ft-lbs
Most common automotive fasteners
Torque Wrench (1/2" Drive)
Range: 30-250 ft-lbs
Large fasteners, wheels
Angle Gauge
Torque-to-yield (TTY) bolts
Torque Wrench Care
- Calibrate annually or after 5,000 clicks
- Store at lowest setting
- Keep clean and lubricated
Search Specifications
Search by component name, bolt size, or description
Type to search through torque specifications. Use arrow keys to navigate results. Press Enter to select a result.
Torque Calculator
Convert between different torque units
3.9l Engine
Torque specifications for 3.9L Engine
3.9l Engine
Torque specifications for 3.9L Engine
Cylinder Head
1 Cylinder Head Bolts
M10 x 1.5
1
Cylinder Head Bolts
M10 x 1.5
Torque Specification
1. 20 ft-lbs (27 N·m)
2. 90°
Important Notes
Follow the manufacturer's specified torque sequence to ensure even clamping force.
2 Rocker Arms/Shafts Bolts
M8 x 1.25
2
Rocker Arms/Shafts Bolts
M8 x 1.25
Torque Specification
21 ft-lbs (28 N·m)
Important Notes
Ensure rocker arms are properly aligned before tightening.
Crankshaft And Bearings
1 Main Bearing Bolts
M12 x 1.75
1
Main Bearing Bolts
M12 x 1.75
Torque Specification
100 ft-lbs (135 N·m)
Important Notes
Follow the specified torque sequence to ensure proper crankshaft alignment.
2 Connecting Rod Nuts
M10 x 1.25
2
Connecting Rod Nuts
M10 x 1.25
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Ensure connecting rods are properly aligned before tightening.
3 Flywheel Bolts
M12 x 1.75
3
Flywheel Bolts
M12 x 1.75
Torque Specification
90 ft-lbs (122 N·m)
Important Notes
Use thread locker on flywheel bolts to prevent loosening.
Timing System
1 Timing Chain Tensioner Bolt
M8 x 1.25
1
Timing Chain Tensioner Bolt
M8 x 1.25
Torque Specification
21 ft-lbs (28 N·m)
Important Notes
Ensure the tensioner is properly seated before tightening.
2 Camshaft Sprocket Bolt
M10 x 1.25
2
Camshaft Sprocket Bolt
M10 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the camshaft sprocket is properly aligned before tightening.
Oil System
1 Oil Pan Bolts
M6 x 1.0
1
Oil Pan Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten bolts in a crisscross pattern to ensure even sealing.
2 Oil Filter Housing Bolt
M8 x 1.25
2
Oil Filter Housing Bolt
M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure the housing is properly aligned before tightening.
Intake And Exhaust
1 Intake Manifold Bolts
M6 x 1.0
1
Intake Manifold Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten bolts in a crisscross pattern to ensure even sealing.
2 Exhaust Manifold Bolts
M8 x 1.25
2
Exhaust Manifold Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure the exhaust manifold is properly aligned before tightening.
4.7l Engine
Torque specifications for 4.7L Engine
4.7l Engine
Torque specifications for 4.7L Engine
Cylinder Head
1 Cylinder Head Bolts
M10 x 1.25
1
Cylinder Head Bolts
M10 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Critical for preventing head gasket failure.
2 Valve Cover Bolts
M8 x 1.0
2
Valve Cover Bolts
M8 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Prevents oil leaks and protects the valve train.
Crankshaft
1 Main Bearing Bolts
M14 x 1.5
1
Main Bearing Bolts
M14 x 1.5
Torque Specification
100 ft-lbs (135 N·m)
Important Notes
Ensures crankshaft rotates smoothly.
2 Connecting Rod Nuts
M10 x 1.25
2
Connecting Rod Nuts
M10 x 1.25
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Ensures pistons move smoothly.
Timing System
1 Camshaft Sprocket Bolt
M10 x 1.25
1
Camshaft Sprocket Bolt
M10 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensures camshaft rotates in sync with crankshaft.
Accessory Mounts
1 Alternator Mounting Bolts
M8 x 1.0
1
Alternator Mounting Bolts
M8 x 1.0
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Ensures proper belt tension and alternator alignment.
45rfe Transmission
Torque specifications for 45rfe Transmission
45rfe Transmission
Torque specifications for 45rfe Transmission
Transmission Mounting
1 Transmission Mounting Bolts
M10 x 1.5
1
Transmission Mounting Bolts
M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure proper alignment of the transmission before tightening.
Oil Pan
1 Transmission Oil Pan Bolts
M6 x 1.0
1
Transmission Oil Pan Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Use a new gasket and ensure the pan surface is clean before installation.
Fluid Management
1 Transmission Drain Plug
M12 x 1.5
1
Transmission Drain Plug
M12 x 1.5
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the plug is properly sealed to prevent leaks.
2 Transmission Fill Plug
M12 x 1.5
2
Transmission Fill Plug
M12 x 1.5
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the plug is properly sealed to prevent leaks.
3 Transmission Cooler Line Fittings
M14 x 1.5
3
Transmission Cooler Line Fittings
M14 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure proper alignment of the cooler lines to prevent leaks.
Drivetrain Connection
1 Drive Axle/Half Shaft Bolts
M12 x 1.5
1
Drive Axle/Half Shaft Bolts
M12 x 1.5
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Ensure proper alignment of the drive axles before tightening.
2 Propeller/Drive Shaft Bolts
M12 x 1.5
2
Propeller/Drive Shaft Bolts
M12 x 1.5
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Ensure proper alignment of the drive shaft before tightening.
Starter Motor
1 Starter Motor Mounting Bolts
M10 x 1.5
1
Starter Motor Mounting Bolts
M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure proper alignment of the starter motor before tightening.
Torque Converter
1 Torque Converter Bolts
M8 x 1.25
1
Torque Converter Bolts
M8 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Estimated value based on similar components. Ensure proper alignment of the torque converter before tightening.
Bell Housing
1 Bell Housing Bolts
M10 x 1.5
1
Bell Housing Bolts
M10 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Estimated value based on similar components. Ensure proper alignment of the bell housing before tightening.
Valve Body
1 Transmission Valve Body Bolts
M6 x 1.0
1
Transmission Valve Body Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure proper alignment of the valve body before tightening.
Output Shaft
1 Output Shaft Nut
M20 x 1.5
1
Output Shaft Nut
M20 x 1.5
Torque Specification
180 ft-lbs (244 N·m)
Important Notes
Ensure proper alignment of the output shaft before tightening.
46re Transmission
Torque specifications for 46re Transmission
46re Transmission
Torque specifications for 46re Transmission
Transmission Mounting
1 Transmission Mounting Bolts
M10 x 1.5
1
Transmission Mounting Bolts
M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the transmission is properly aligned before tightening.
Oil Pan
1 Transmission Oil Pan Bolts
M6 x 1.0
1
Transmission Oil Pan Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Use a crisscross pattern to ensure even sealing.
2 Transmission Drain Plug
M12 x 1.5
2
Transmission Drain Plug
M12 x 1.5
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the plug is properly seated before tightening.
3 Transmission Fill Plug
M12 x 1.5
3
Transmission Fill Plug
M12 x 1.5
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the plug is properly seated before tightening.
Flywheel And Torque Converter
1 Flywheel Bolts
M10 x 1.25
1
Flywheel Bolts
M10 x 1.25
Torque Specification
90 ft-lbs (122 N·m)
Important Notes
Use a crisscross pattern to ensure even clamping force.
2 Torque Converter Bolts
M8 x 1.25
2
Torque Converter Bolts
M8 x 1.25
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
Estimated value based on similar components. Ensure the torque converter is properly seated before tightening.
Starter Motor
1 Starter Motor Mounting Bolts
M10 x 1.5
1
Starter Motor Mounting Bolts
M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the starter motor is properly aligned before tightening.
Drive Axle And Shaft
1 Drive Axle/Half Shaft Bolts
M12 x 1.5
1
Drive Axle/Half Shaft Bolts
M12 x 1.5
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Ensure the axle is properly seated before tightening.
2 Propeller/Drive Shaft Bolts
M12 x 1.5
2
Propeller/Drive Shaft Bolts
M12 x 1.5
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Ensure the drive shaft is properly aligned before tightening.
Bell Housing
1 Bell Housing Bolts
M10 x 1.5
1
Bell Housing Bolts
M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Use a crisscross pattern to ensure even clamping force.
Valve Body
1 Valve Body Bolts
M6 x 1.0
1
Valve Body Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Use a crisscross pattern to ensure even clamping force.
Cooler Lines
1 Transmission Cooler Line Fittings
M12 x 1.5
1
Transmission Cooler Line Fittings
M12 x 1.5
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the fittings are properly seated before tightening.
Shift Linkage
1 Shift Linkage Bolts
M6 x 1.0
1
Shift Linkage Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure the linkage is properly aligned before tightening.
Range Sensor
1 Transmission Range Sensor Bolts
M6 x 1.0
1
Transmission Range Sensor Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure the sensor is properly aligned before tightening.
Output Shaft Retainer
1 Output Shaft Retainer Bolts
M8 x 1.25
1
Output Shaft Retainer Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure the retainer is properly seated before tightening.
5.2l Engine
Torque specifications for 5.2L Engine
5.2l Engine
Torque specifications for 5.2L Engine
Cylinder Head
1 Cylinder Head Bolts
M10 x 1.5
1
Cylinder Head Bolts
M10 x 1.5
Torque Specification
1. 20 ft-lbs (27 N·m)
2. 90°
Important Notes
Torque sequence must be followed as per the manufacturer's specifications. Final step involves a 90-degree angle tightening.
Crankshaft And Bearings
1 Main Bearing Bolts
M12 x 1.75
1
Main Bearing Bolts
M12 x 1.75
Torque Specification
100 ft-lbs (135 N·m)
Important Notes
Ensure proper alignment of bearing caps before torquing.
2 Connecting Rod Nuts
M8 x 1.25
2
Connecting Rod Nuts
M8 x 1.25
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Ensure proper alignment of connecting rods before torquing.
Flywheel And Flexplate
1 Flywheel Bolts
M10 x 1.5
1
Flywheel Bolts
M10 x 1.5
Torque Specification
90 ft-lbs (122 N·m)
Important Notes
Ensure flywheel is properly aligned before torquing.
Oil System
1 Oil Pan Bolts
M6 x 1.0
1
Oil Pan Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure oil pan gasket is properly seated before torquing.
2 Oil Pump Bolts
M8 x 1.25
2
Oil Pump Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure oil pump is properly aligned before torquing.
Valve Train
1 Valve Cover Bolts
M6 x 1.0
1
Valve Cover Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure valve cover gasket is properly seated before torquing.
2 Rocker Arms/Shafts Bolts
M8 x 1.25
2
Rocker Arms/Shafts Bolts
M8 x 1.25
Torque Specification
21 ft-lbs (28 N·m)
Important Notes
Ensure rocker arms are properly aligned before torquing.
Timing System
1 Timing Belt/Chain Tensioner Bolt
M8 x 1.25
1
Timing Belt/Chain Tensioner Bolt
M8 x 1.25
Torque Specification
21 ft-lbs (28 N·m)
Important Notes
Ensure tensioner is properly aligned before torquing.
2 Camshaft Sprocket Bolt
M10 x 1.5
2
Camshaft Sprocket Bolt
M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure sprocket is properly aligned before torquing.
Accessory Drives
1 Alternator Mounting Bolts
M8 x 1.25
1
Alternator Mounting Bolts
M8 x 1.25
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Ensure alternator is properly aligned before torquing.
2 Power Steering Pump Mounting Bolts
M8 x 1.25
2
Power Steering Pump Mounting Bolts
M8 x 1.25
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Ensure power steering pump is properly aligned before torquing.
3 A/C Compressor Mounting Bolts
M8 x 1.25
3
A/C Compressor Mounting Bolts
M8 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure A/C compressor is properly aligned before torquing.
Intake And Exhaust
1 Intake Manifold Bolts
M6 x 1.0
1
Intake Manifold Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure intake manifold gasket is properly seated before torquing.
2 Exhaust Manifold/Headers Bolts
M8 x 1.25
2
Exhaust Manifold/Headers Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure exhaust manifold gasket is properly seated before torquing.
Cooling System
1 Water Pump Bolts
M6 x 1.0
1
Water Pump Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure water pump gasket is properly seated before torquing.
2 Thermostat Housing Bolts
M6 x 1.0
2
Thermostat Housing Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure thermostat housing gasket is properly seated before torquing.
Sensors And Electronics
1 Crankshaft Position Sensor Bolt
M6 x 1.0
1
Crankshaft Position Sensor Bolt
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure sensor is properly aligned before torquing.
2 Camshaft Position Sensor Bolt
M6 x 1.0
2
Camshaft Position Sensor Bolt
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure sensor is properly aligned before torquing.
Fuel System
1 Fuel Pressure Regulator Bolts
M6 x 1.0
1
Fuel Pressure Regulator Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure fuel pressure regulator is properly aligned before torquing.
Starter And Charging
1 Starter Motor Mounting Bolts
M8 x 1.25
1
Starter Motor Mounting Bolts
M8 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure starter motor is properly aligned before torquing.
5.9l Engine
Torque specifications for 5.9L Engine
5.9l Engine
Torque specifications for 5.9L Engine
Cylinder Head
1 Cylinder Head Bolts
M10 x 1.5
1
Cylinder Head Bolts
M10 x 1.5
Torque Specification
1. 20 ft-lbs (27 N·m)
2. 90°
Important Notes
Follow the manufacturer's torque sequence for cylinder head bolts. Failure to do so may result in head gasket failure.
2 Rocker Arms/Shafts Bolts
M8 x 1.25
2
Rocker Arms/Shafts Bolts
M8 x 1.25
Torque Specification
21 ft-lbs (28 N·m)
Important Notes
Ensure rocker arms are properly aligned before tightening.
Crankshaft And Bearings
1 Main Bearing Bolts
M12 x 1.75
1
Main Bearing Bolts
M12 x 1.75
Torque Specification
100 ft-lbs (135 N·m)
Important Notes
Follow the manufacturer's torque sequence for main bearing bolts.
2 Connecting Rod Nuts
M10 x 1.25
2
Connecting Rod Nuts
M10 x 1.25
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Ensure connecting rods are properly aligned before tightening.
3 Flywheel Bolts
M12 x 1.75
3
Flywheel Bolts
M12 x 1.75
Torque Specification
90 ft-lbs (122 N·m)
Important Notes
Use thread locker on flywheel bolts to prevent loosening.
Timing System
1 Timing Chain Tensioner Bolt
M8 x 1.25
1
Timing Chain Tensioner Bolt
M8 x 1.25
Torque Specification
21 ft-lbs (28 N·m)
Important Notes
Ensure the tensioner is properly seated before tightening.
2 Camshaft Sprocket Bolt
M10 x 1.25
2
Camshaft Sprocket Bolt
M10 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the camshaft sprocket is properly aligned before tightening.
Oil System
1 Oil Pan Bolts
M6 x 1.0
1
Oil Pan Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten bolts in a crisscross pattern to ensure even sealing.
2 Oil Pump Bolts
M8 x 1.25
2
Oil Pump Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure the oil pump is properly aligned before tightening.
Intake And Exhaust
1 Intake Manifold Bolts
M6 x 1.0
1
Intake Manifold Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten bolts in a crisscross pattern to ensure even sealing.
2 Exhaust Manifold Bolts
M8 x 1.25
2
Exhaust Manifold Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Tighten bolts in a crisscross pattern to ensure even sealing.
545rfe Transmission
Torque specifications for 545rfe Transmission
545rfe Transmission
Torque specifications for 545rfe Transmission
Transmission Mounting
1 Transmission Mounting Bolts
M10 x 1.5
1
Transmission Mounting Bolts
M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure proper alignment of the transmission during installation.
Oil Pan
1 Transmission Oil Pan Bolts
M6 x 1.0
1
Transmission Oil Pan Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Use a crisscross pattern to ensure even sealing of the oil pan gasket.
Fluid Plugs
1 Transmission Drain Plug
M12 x 1.75
1
Transmission Drain Plug
M12 x 1.75
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the plug is properly seated before torquing.
2 Transmission Fill Plug
M12 x 1.75
2
Transmission Fill Plug
M12 x 1.75
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the plug is properly seated before torquing.
Driveline
1 Drive Axle/Half Shaft Bolts
M12 x 1.75
1
Drive Axle/Half Shaft Bolts
M12 x 1.75
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Ensure proper alignment of the drive axles during installation.
2 Propeller/Drive Shaft Bolts
M12 x 1.75
2
Propeller/Drive Shaft Bolts
M12 x 1.75
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Ensure proper alignment of the drive shaft during installation.
Starter Motor
1 Starter Motor Mounting Bolts
M10 x 1.5
1
Starter Motor Mounting Bolts
M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure proper alignment of the starter motor during installation.
Torque Converter
1 Torque Converter Bolts
M8 x 1.25
1
Torque Converter Bolts
M8 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure proper alignment of the torque converter during installation.
Bell Housing
1 Bell Housing Bolts
M10 x 1.5
1
Bell Housing Bolts
M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure proper alignment of the bell housing during installation.
Valve Body
1 Valve Body Bolts
M6 x 1.0
1
Valve Body Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Use a crisscross pattern to ensure even sealing of the valve body gasket.
Output Shaft
1 Output Shaft Nut
M24 x 2.0
1
Output Shaft Nut
M24 x 2.0
Torque Specification
180 ft-lbs (244 N·m)
Important Notes
Ensure the output shaft is properly seated before torquing.
Shift Linkage
1 Shift Linkage Bolts
M6 x 1.0
1
Shift Linkage Bolts
M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure proper alignment of the shift linkage during installation.
Body
Torque specifications for Body
Body
Torque specifications for Body
Wheels And Hubs
1 Wheel Lug Nuts
M12 x 1.5
1
Wheel Lug Nuts
M12 x 1.5
Torque Specification
100 ft-lbs (135 N·m)
Important Notes
Ensure lug nuts are tightened in a star pattern to evenly distribute torque.
Fuel System
1 Fuel Tank Strap Bolts
M8 x 1.25
1
Fuel Tank Strap Bolts
M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure fuel tank is properly aligned before tightening.
2 Fuel Filler Neck Bolts
M6 x 1.0
2
Fuel Filler Neck Bolts
M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure proper sealing of the fuel filler neck to prevent leaks.
Electrical System
1 Battery Terminal Nuts
M6 x 1.0
1
Battery Terminal Nuts
M6 x 1.0
Torque Specification
6.25 ft-lbs (8.5 N·m)
Important Notes
Ensure terminals are clean and free of corrosion before tightening.
Body Panels
1 Body Panel Bolts
M6 x 1.0
1
Body Panel Bolts
M6 x 1.0
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value based on similar components. Ensure panels are aligned before tightening.
Seats
1 Seat Mounting Bolts
M8 x 1.25
1
Seat Mounting Bolts
M8 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Estimated value based on similar components. Ensure seats are properly aligned before tightening.
Bumpers
1 Bumper Mounting Bolts
M8 x 1.25
1
Bumper Mounting Bolts
M8 x 1.25
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Estimated value based on similar components. Ensure bumpers are properly aligned before tightening.
Doors
1 Door Hinge Bolts
M8 x 1.25
1
Door Hinge Bolts
M8 x 1.25
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Estimated value based on similar components. Ensure doors are properly aligned before tightening.
Radiator Support
1 Radiator Support Bolts
M6 x 1.0
1
Radiator Support Bolts
M6 x 1.0
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value based on similar components. Ensure radiator is properly aligned before tightening.
Roof Rack
1 Roof Rack Mounting Bolts
M6 x 1.0
1
Roof Rack Mounting Bolts
M6 x 1.0
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value based on similar components. Ensure roof rack is properly aligned before tightening.
Mirrors
1 Mirror Mounting Bolts
M6 x 1.0
1
Mirror Mounting Bolts
M6 x 1.0
Torque Specification
13 ft-lbs (17 N·m)
Important Notes
Estimated value based on similar components. Ensure mirrors are properly aligned before tightening.
Brakes
Torque specifications for Brakes
Brakes
Torque specifications for Brakes
Brake Caliper
1 Brake Caliper Bolts
M10 x 1.25
1
Brake Caliper Bolts
M10 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
These bolts secure the brake caliper to the mounting bracket. Ensure proper alignment before torquing.
2 Brake Caliper Mounting Bracket Bolts
M12 x 1.5
2
Brake Caliper Mounting Bracket Bolts
M12 x 1.5
Torque Specification
100 ft-lbs (135 N·m)
Important Notes
These bolts attach the caliper mounting bracket to the steering knuckle or axle. Ensure the bracket is properly seated before torquing.
Brake Rotor Drum
1 Brake Disc/Drum Retaining Bolts
M8 x 1.25
1
Brake Disc/Drum Retaining Bolts
M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
These bolts secure the brake rotor or drum to the wheel hub. Ensure the rotor/drum is properly seated before torquing.
Brake Hydraulics
1 Brake Hose Banjo Bolt
M10 x 1.0
1
Brake Hose Banjo Bolt
M10 x 1.0
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
This bolt connects the brake hose to the caliper or wheel cylinder. Ensure the sealing washers are properly seated before torquing.
2 Brake Master Cylinder Mounting Bolts
M8 x 1.25
2
Brake Master Cylinder Mounting Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
These bolts secure the master cylinder to the brake booster. Ensure the master cylinder is properly aligned before torquing.
3 Brake Line Fittings
M10 x 1.0
3
Brake Line Fittings
M10 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
These fittings connect the brake lines to various components. Ensure the fittings are properly aligned before torquing.
Brake Booster
1 Brake Booster Mounting Bolts
M8 x 1.25
1
Brake Booster Mounting Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
These bolts secure the brake booster to the firewall. Ensure the booster is properly aligned before torquing.
Parking Brake
1 Parking Brake Cable Bracket Bolts
M8 x 1.25
1
Parking Brake Cable Bracket Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
These bolts secure the parking brake cable brackets to the chassis or axle. Ensure the brackets are properly aligned before torquing.
Wheel Assembly
1 Wheel Lug Nuts
M12 x 1.5
1
Wheel Lug Nuts
M12 x 1.5
Torque Specification
100 ft-lbs (135 N·m)
Important Notes
These nuts secure the wheel to the hub. Use a star pattern to ensure even torque distribution.
Drivetrain
Torque specifications for Drivetrain
Drivetrain
Torque specifications for Drivetrain
Flywheel
1 Flywheel Bolts
M12 x 1.5
1
Flywheel Bolts
M12 x 1.5
Torque Specification
90 ft-lbs (122 N·m)
Important Notes
Ensure the flywheel is properly aligned before tightening.
Transmission
1 Transmission Mounting Bolts
M10 x 1.25
1
Transmission Mounting Bolts
M10 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the transmission is properly aligned before tightening.
2 Transmission Oil Pan Bolts
M6 x 1.0
2
Transmission Oil Pan Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Torque values are critical to prevent leaks.
3 Transmission Drain and Fill Plugs
M12 x 1.5
3
Transmission Drain and Fill Plugs
M12 x 1.5
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the threads are clean and free of debris.
4 Transmission Bellhousing Bolts
M10 x 1.25
4
Transmission Bellhousing Bolts
M10 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Estimated value based on similar components.
Drive Axles
1 Drive Axle/Half Shaft Bolts
M12 x 1.5
1
Drive Axle/Half Shaft Bolts
M12 x 1.5
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Ensure the axle is properly seated before tightening.
2 CV Joint/Axle Nut
M24 x 1.5
2
CV Joint/Axle Nut
M24 x 1.5
Torque Specification
180 ft-lbs (244 N·m)
Important Notes
Use a torque wrench with a high-capacity range.
Propeller Shaft
1 Propeller/Drive Shaft Bolts
M10 x 1.25
1
Propeller/Drive Shaft Bolts
M10 x 1.25
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Ensure the drive shaft is properly aligned before tightening.
Differential
1 Differential Drain/Fill Plug
M12 x 1.5
1
Differential Drain/Fill Plug
M12 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure the threads are clean and free of debris.
2 Differential Cover Bolts
M8 x 1.25
2
Differential Cover Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated value based on similar components.
3 Differential Pinion Flange Nut
M24 x 1.5
3
Differential Pinion Flange Nut
M24 x 1.5
Torque Specification
200 ft-lbs (271 N·m)
Important Notes
Use a torque wrench with a high-capacity range.
Transfer Case
1 Transfer Case Drain/Fill Plug
M12 x 1.5
1
Transfer Case Drain/Fill Plug
M12 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure the threads are clean and free of debris.
2 Transfer Case Mounting Bolts
M10 x 1.25
2
Transfer Case Mounting Bolts
M10 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Estimated value based on similar components.
3 Transfer Case Output Shaft Flange Bolts
M10 x 1.25
3
Transfer Case Output Shaft Flange Bolts
M10 x 1.25
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Ensure the flange is properly aligned before tightening.
Starter Motor
1 Starter Motor Mounting Bolts
M10 x 1.25
1
Starter Motor Mounting Bolts
M10 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the starter motor is properly aligned before tightening.
Electrical
Torque specifications for Electrical
Electrical
Torque specifications for Electrical
Ignition System
1 Ignition Coil Bolt
M6 x 1.0
1
Ignition Coil Bolt
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure the ignition coil is seated properly before torquing.
Starting System
1 Starter Motor Mounting Bolts
M10 x 1.5
1
Starter Motor Mounting Bolts
M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the starter motor is properly aligned with the flywheel before torquing.
Charging System
1 Alternator Mounting Bolts
M8 x 1.25
1
Alternator Mounting Bolts
M8 x 1.25
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Ensure the alternator is properly aligned with the drive belt before torquing.
Battery System
1 Battery Terminal Nuts
M6 x 1.0
1
Battery Terminal Nuts
M6 x 1.0
Torque Specification
6.25 ft-lbs (8.5 N·m)
Important Notes
Ensure the battery terminals are clean and free of corrosion before torquing.
Ac System
1 A/C Compressor Mounting Bolts
M10 x 1.5
1
A/C Compressor Mounting Bolts
M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the A/C compressor is properly aligned with the drive belt before torquing.
2 A/C Line Fittings
M12 x 1.5
2
A/C Line Fittings
M12 x 1.5
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Ensure the A/C lines are properly aligned and seated before torquing.
Grounding System
1 Ground Strap Bolts
M6 x 1.0
1
Ground Strap Bolts
M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the grounding surface is clean and free of corrosion before torquing.
Fuse And Relay System
1 Fuse Box Mounting Bolts
M6 x 1.0
1
Fuse Box Mounting Bolts
M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Ensure the fuse box is properly aligned with the mounting holes before torquing.
Wiring Harness System
1 Wiring Harness Clamp Bolts
M5 x 0.8
1
Wiring Harness Clamp Bolts
M5 x 0.8
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Ensure the wiring harness is properly routed and secured before torquing.
Engine Control System
1 ECU/ECM Mounting Bolts
M6 x 1.0
1
ECU/ECM Mounting Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure the ECU/ECM is properly seated and aligned before torquing.
2 Sensor Mounting Bolts (e.g., Crankshaft Position Sensor, Camshaft Position Sensor)
M6 x 1.0
2
Sensor Mounting Bolts (e.g., Crankshaft Position Sensor, Camshaft Position Sensor)
M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Ensure the sensor is properly seated and aligned before torquing.
Emissions Sensors
Torque specifications for Emissions_sensors
Emissions Sensors
Torque specifications for Emissions_sensors
Egr System
1 EGR Valve Bolts
M6 x 1.0
1
EGR Valve Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure the EGR valve gasket is properly seated before tightening.
Exhaust Manifold
1 Exhaust Manifold/Headers Bolts
M8 x 1.25
1
Exhaust Manifold/Headers Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Follow the manufacturer's torque sequence to avoid warping the manifold.
2 Exhaust Manifold/Headers to Cylinder Head Bolts
M8 x 1.25
2
Exhaust Manifold/Headers to Cylinder Head Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure the gasket is properly seated before tightening.
3 Exhaust Pipe to Exhaust Manifold/Headers Bolts
M8 x 1.25
3
Exhaust Pipe to Exhaust Manifold/Headers Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure the gasket is properly seated before tightening.
Catalytic Converter
1 Catalytic Converter to Exhaust Pipe Bolts
M10 x 1.5
1
Catalytic Converter to Exhaust Pipe Bolts
M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the gasket is properly seated before tightening.
Intake System
1 Throttle Body Bolts
M6 x 1.0
1
Throttle Body Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure the throttle body gasket is properly seated before tightening.
2 Intake Manifold Bolts
M6 x 1.0
2
Intake Manifold Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Follow the manufacturer's torque sequence to avoid warping the manifold.
Emissions Sensors
1 Oxygen Sensor (O2 Sensor) Mounting Nut
M12 x 1.25
1
Oxygen Sensor (O2 Sensor) Mounting Nut
M12 x 1.25
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Ensure the sensor is properly seated before tightening.
2 Mass Air Flow (MAF) Sensor Mounting Screws
M4 x 0.7
2
Mass Air Flow (MAF) Sensor Mounting Screws
M4 x 0.7
Torque Specification
0.83 ft-lbs (1.1 N·m)
Important Notes
Ensure the MAF sensor is properly aligned before tightening.
3 Evaporative Emissions (EVAP) Canister Purge Valve Bolts
M6 x 1.0
3
Evaporative Emissions (EVAP) Canister Purge Valve Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure the purge valve is properly seated before tightening.
4 PCV Valve Mounting Bolt
M6 x 1.0
4
PCV Valve Mounting Bolt
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure the PCV valve is properly seated before tightening.
Exhaust
Torque specifications for Exhaust
Exhaust
Torque specifications for Exhaust
Exhaust Manifold
1 Exhaust Manifold/Headers to Cylinder Head Bolts
M10 x 1.25
1
Exhaust Manifold/Headers to Cylinder Head Bolts
M10 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to evenly distribute pressure.
2 Exhaust Pipe to Exhaust Manifold/Headers Bolts
M10 x 1.25
2
Exhaust Pipe to Exhaust Manifold/Headers Bolts
M10 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure gasket is properly seated before tightening.
Catalytic Converter
1 Catalytic Converter to Exhaust Pipe Bolts
M12 x 1.5
1
Catalytic Converter to Exhaust Pipe Bolts
M12 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure gasket is properly seated before tightening.
Muffler
1 Muffler to Exhaust Pipe Bolts
M12 x 1.5
1
Muffler to Exhaust Pipe Bolts
M12 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure gasket is properly seated before tightening.
Exhaust Hangers
1 Exhaust Hanger Bolts
M8 x 1.25
1
Exhaust Hanger Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value based on typical M8 bolt torque specifications.
Oxygen Sensor
1 Oxygen Sensor (O2 Sensor)
M18 x 1.5
1
Oxygen Sensor (O2 Sensor)
M18 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Estimated value based on typical oxygen sensor torque specifications.
Heat Shields
1 Exhaust Heat Shield Bolts
M6 x 1.0
1
Exhaust Heat Shield Bolts
M6 x 1.0
Torque Specification
12 ft-lbs (16 N·m)
Important Notes
Estimated value based on typical M6 bolt torque specifications.
Exhaust Flanges
1 Exhaust Flange Bolts
M10 x 1.25
1
Exhaust Flange Bolts
M10 x 1.25
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
Estimated value based on typical M10 bolt torque specifications.
Fuel
Torque specifications for Fuel
Fuel
Torque specifications for Fuel
Fuel Rail System
1 Fuel Rail Bolts
M6 x 1.0
1
Fuel Rail Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to evenly distribute pressure.
2 Fuel Injector Bolts
M6 x 1.0
2
Fuel Injector Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure injectors are properly seated before tightening.
3 Fuel Injector Rail Bolts
M6 x 1.0
3
Fuel Injector Rail Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten in a crisscross pattern to ensure even pressure distribution.
Fuel Pump And Tank System
1 Fuel Pump Mounting Bolts
M8 x 1.25
1
Fuel Pump Mounting Bolts
M8 x 1.25
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Ensure the fuel pump is properly seated before tightening.
2 Fuel Tank Strap Bolts
M8 x 1.25
2
Fuel Tank Strap Bolts
M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure the tank is properly aligned before tightening.
3 Fuel Tank Sender Unit Bolts
M6 x 1.0
3
Fuel Tank Sender Unit Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure the sender unit is properly seated before tightening.
Fuel Delivery System
1 Fuel Filler Neck Bolts
M6 x 1.0
1
Fuel Filler Neck Bolts
M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the filler neck is properly aligned before tightening.
2 Fuel Filter Bolt/Nut
M8 x 1.25
2
Fuel Filter Bolt/Nut
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the filter is properly seated before tightening.
3 Fuel Line Fittings
M6 x 1.0
3
Fuel Line Fittings
M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure fittings are properly aligned and seated before tightening.
Emissions Control System
1 Fuel Pressure Regulator Bolts
M6 x 1.0
1
Fuel Pressure Regulator Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure the regulator is properly seated before tightening.
2 Fuel Vapor Canister Bolts
M6 x 1.0
2
Fuel Vapor Canister Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure the canister is properly seated before tightening.
Electrical Components
1 Fuel Pump Relay Mounting Bolts
M6 x 1.0
1
Fuel Pump Relay Mounting Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure the relay is properly seated before tightening.
Hvac
Torque specifications for Hvac
Hvac
Torque specifications for Hvac
Ac Compressor
1 A/C Compressor Mounting Bolts
M10 x 1.5
1
A/C Compressor Mounting Bolts
M10 x 1.5
Torque Specification
40 ft-lbs (54 N-m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to evenly distribute load.
Ac Lines
1 A/C Line Fittings
M12 x 1.5
1
A/C Line Fittings
M12 x 1.5
Torque Specification
45 ft-lbs (61 N-m)
Important Notes
Use a backup wrench to prevent twisting of the refrigerant lines during tightening.
Evaporator Core
1 Evaporator Core Housing Bolts
M6 x 1.0
1
Evaporator Core Housing Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N-m)
Important Notes
Torque value is estimated based on similar components. Ensure housing is properly sealed to prevent air leaks.
Blower Motor
1 Blower Motor Mounting Bolts
M6 x 1.0
1
Blower Motor Mounting Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N-m)
Important Notes
Torque value is estimated based on similar components. Ensure motor is securely mounted to prevent vibrations.
Heater Core
1 Heater Core Inlet/Outlet Fittings
M8 x 1.25
1
Heater Core Inlet/Outlet Fittings
M8 x 1.25
Torque Specification
15 ft-lbs (20 N-m)
Important Notes
Torque value is estimated based on similar components. Ensure fittings are properly sealed to prevent coolant leaks.
Hvac Case
1 HVAC Case Assembly Bolts
M6 x 1.0
1
HVAC Case Assembly Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N-m)
Important Notes
Torque value is estimated based on similar components. Ensure case is properly sealed to prevent air leaks.
Suspension
Torque specifications for Suspension
Suspension
Torque specifications for Suspension
Strut Shock Assembly
1 Strut/Shock Absorber Mounting Bolts
M12 x 1.5
1
Strut/Shock Absorber Mounting Bolts
M12 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Ensure bolts are tightened evenly to avoid misalignment.
2 Upper Strut Mount Bolts
M10 x 1.25
2
Upper Strut Mount Bolts
M10 x 1.25
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Estimated value based on similar components. Ensure bolts are tightened evenly.
3 Lower Shock Mounting Bolts
M10 x 1.25
3
Lower Shock Mounting Bolts
M10 x 1.25
Torque Specification
55 ft-lbs (75 N·m)
Important Notes
Estimated value based on similar components. Ensure bolts are tightened evenly.
Control Arm Assembly
1 Control Arm Bolts
M14 x 1.5
1
Control Arm Bolts
M14 x 1.5
Torque Specification
1. 50 ft-lbs (68 N·m)
2. 90°
Important Notes
Follow the torque sequence to ensure even clamping force.
2 Ball Joint Nut
M12 x 1.25
2
Ball Joint Nut
M12 x 1.25
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Ensure the ball joint is properly seated before tightening.
Steering Components
1 Tie Rod End Nut
M10 x 1.25
1
Tie Rod End Nut
M10 x 1.25
Torque Specification
55 ft-lbs (75 N·m)
Important Notes
Ensure the tie rod end is properly seated before tightening.
2 Steering Gear/Rack Bolts
M12 x 1.5
2
Steering Gear/Rack Bolts
M12 x 1.5
Torque Specification
1. 45 ft-lbs (61 N·m)
2. 90°
Important Notes
Follow the torque sequence to ensure even clamping force.
Sway Bar Assembly
1 Sway Bar Link Nut
M10 x 1.25
1
Sway Bar Link Nut
M10 x 1.25
Torque Specification
55 ft-lbs (75 N·m)
Important Notes
Ensure the sway bar link is properly seated before tightening.
2 Sway Bar Bracket Bolts
M8 x 1.25
2
Sway Bar Bracket Bolts
M8 x 1.25
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Estimated value based on similar components. Ensure bolts are tightened evenly.
Wheel And Axle Assembly
1 Wheel Lug Nuts
M12 x 1.5
1
Wheel Lug Nuts
M12 x 1.5
Torque Specification
100 ft-lbs (135 N·m)
Important Notes
Use a star pattern to tighten lug nuts evenly.
2 Drive Axle/Half Shaft Bolts
M10 x 1.25
2
Drive Axle/Half Shaft Bolts
M10 x 1.25
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Ensure the axle is properly seated before tightening.
3 CV Joint/Axle Nut
M24 x 1.5
3
CV Joint/Axle Nut
M24 x 1.5
Torque Specification
180 ft-lbs (244 N·m)
Important Notes
Use a torque wrench capable of handling high torque values.
Leaf Spring Assembly
1 Leaf Spring U-Bolts
M12 x 1.75
1
Leaf Spring U-Bolts
M12 x 1.75
Torque Specification
90 ft-lbs (122 N·m)
Important Notes
Ensure U-bolts are tightened evenly to avoid misalignment.
Track Bar Assembly
1 Track Bar Bolts
M12 x 1.5
1
Track Bar Bolts
M12 x 1.5
Torque Specification
75 ft-lbs (102 N·m)
Important Notes
Estimated value based on similar components. Ensure bolts are tightened evenly.
Troubleshooting Guide
Common issues, diagnostic steps, and prevention guidelines
Common Issues
Bolt stretching, stripped threads, uneven torque patterns
Common Issues
Bolt stretching, stripped threads, uneven torque patterns
Loose Components
Symptoms:
- Rattling or vibration noises
- Visible movement in components
- Uneven panel gaps
Solutions:
- Clean threads and mounting surfaces
- Replace damaged fasteners
- Apply proper torque in sequence
- Use thread locker if specified
Stripped Fasteners
Symptoms:
- Unable to achieve proper torque
- Fastener spins freely
- Visible thread damage
Solutions:
- Use thread repair kit if appropriate
- Install thread insert (HeliCoil)
- Replace component if threaded hole is damaged
- Upgrade to higher grade fastener if recommended
Overtightened Components
Symptoms:
- Cracked or deformed parts
- Broken fasteners
- Compressed gaskets or seals
Solutions:
- Replace damaged components
- Use new fasteners
- Follow proper torque sequence
- Verify correct torque specifications
Diagnostic Steps
Visual inspection, torque verification, thread assessment
Diagnostic Steps
Visual inspection, torque verification, thread assessment
1
Visual Inspection
Inspect the affected area for any visible signs of damage or wear
- Check for cracks or deformation
- Look for signs of excessive wear
- Verify proper fastener installation
2
Torque Verification
Verify the torque applied to the fasteners
- Check the torque wrench calibration
- Verify the torque specification
- Compare the applied torque to the specification
3
Thread Assessment
Assess the condition of the threads
- Check for signs of thread damage
- Verify the thread type and size
- Check for proper thread engagement
Prevention Guidelines
Best practices, maintenance tips, tool care
Prevention Guidelines
Best practices, maintenance tips, tool care
Best Practices
- Always follow the recommended torque specification
- Use the correct type and size of fasteners
- Verify the torque wrench calibration regularly
Maintenance Tips
- Regularly inspect the affected area for signs of wear or damage
- Replace damaged or worn-out components promptly
- Keep the work area clean and organized
Tool Care
- Regularly clean and maintain the torque wrench
- Store the torque wrench in a dry and secure location
- Verify the torque wrench calibration before each use
Frequently Asked Questions
Find answers to common questions about torque specifications
Q1 What IS the proper torque specification for the lug nuts on a 1999 Dodge dakota?
Q1
What IS the proper torque specification for the lug nuts on a 1999 Dodge dakota?
115 ft-lbs (156 Nm)
Q2 What torque wrench should I use for tightening the cylinder head bolts on a 2002 Dodge dakota?
Q2
What torque wrench should I use for tightening the cylinder head bolts on a 2002 Dodge dakota?
A torque wrench with a range of 20-250 ft-lbs (27-339 Nm) and an accuracy of ±3%
Q3 How can I ensure accurate torque readings when working on my 2004 Dodge dakota?
Q3
How can I ensure accurate torque readings when working on my 2004 Dodge dakota?
Calibrate your torque wrench regularly according to the manufacturer's instructions and use a new torque angle gauge for critical bolts.
Q4 What are the torque specifications for the spark plugs on a 1997 Dodge dakota?
Q4
What are the torque specifications for the spark plugs on a 1997 Dodge dakota?
18-22 ft-lbs (24-30 Nm)
Q5 Can I use an impact wrench to tighten the bolts on my 2001 Dodge dakota?
Q5
Can I use an impact wrench to tighten the bolts on my 2001 Dodge dakota?
No, impact wrenches can overtighten bolts and damage threads. Use a calibrated torque wrench for all critical bolts on your Dakota.
Q6 What IS the recommended tightening sequence for the intake manifold bolts on a 2003 Dodge dakota?
Q6
What IS the recommended tightening sequence for the intake manifold bolts on a 2003 Dodge dakota?
Follow the manufacturer's specified sequence and tighten the bolts gradually in multiple passes to achieve the proper torque.
Environmental Considerations
Temperature, humidity, and seasonal effects on torque specifications
Temperature Effects
Includes: High Heat, Cold Weather, Thermal Cycling
Temperature Effects
Includes: High Heat, Cold Weather, Thermal Cycling
Temperature can significantly impact torque values and fastener behavior
Cold Weather
Effects:
- Increased material brittleness
- Higher torque required due to thread contraction
- Reduced thread lubricant effectiveness
Recommendations:
- Allow components to warm to room temperature when possible
- Consider using winter-grade thread lubricants
- Check torque values more frequently during winter months
Hot Weather
Effects:
- Thermal expansion of components
- Decreased friction in threads
- Accelerated lubricant breakdown
Recommendations:
- Check torque when components are at normal operating temperature
- Use temperature-resistant thread lockers
- Consider re-torquing after heat cycles
Humidity and Corrosion
Covers: Rust Prevention, Salt Exposure, Moisture Control
Humidity and Corrosion
Covers: Rust Prevention, Salt Exposure, Moisture Control
Moisture and corrosion can affect fastener integrity and torque values
High Humidity
Effects:
- Accelerated corrosion formation
- Reduced friction coefficient
- Potential thread seizing
Prevention:
- Use corrosion-resistant fasteners
- Apply appropriate anti-seize compounds
- Maintain proper protective coatings
Salt Exposure
Effects:
- Rapid corrosion development
- Thread damage
- Seized fasteners
Prevention:
- Regular underbody washing
- Use of sacrificial anodes where appropriate
- Application of protective coatings
Seasonal Maintenance
Spring, Summer, Fall, and Winter maintenance schedules
Seasonal Maintenance
Spring, Summer, Fall, and Winter maintenance schedules
Spring
- Inspect for winter damage
- Clean and protect exposed fasteners
- Check torque on critical components
Summer
- Monitor heat-affected components
- Check expansion-related loosening
- Inspect cooling system mounts
Fall
- Prepare for winter conditions
- Apply corrosion protection
- Verify all fasteners are properly torqued
Winter
- More frequent inspection of critical fasteners
- Check for salt damage
- Monitor suspension component torque
Related Resources
Tools, service procedures, and technical bulletins
Recommended Tools
Digital Torque Wrench (10-100 Nm)
Essential for tightening fasteners to precise torque specifications, preventing damage and ensuring proper assembly. This range IS suitable for many applications on the dakota.
- Digital display for accurate readings
- Audible alarm when target torque IS reached
- Multiple units (Nm, ft-lb, in-lb)
- Reversible ratcheting mechanism
Service Procedures
Engine Bolt Torque Specifications
Technical procedure overview for engine bolt torque specifications on the Dodge dakota
- Cylinder Head Bolts: 95 Nm (70 ft-lb)
- Intake Manifold Bolts: 25 Nm (18 ft-lb)
- Exhaust Manifold Bolts: 30 Nm (22 ft-lb)
- Oil Pan Bolts: 14 Nm (10 ft-lb)
- Timing Cover Bolts: 10 Nm (7 ft-lb)
Suspension Bolt Torque Specifications
Technical procedure overview for suspension bolt torque specifications on the Dodge dakota
- Control Arm Bolts: 100 Nm (74 ft-lb)
- Ball Joint Nuts: 50 Nm (37 ft-lb)
- Tie Rod Ends: 40 Nm (30 ft-lb)
- Sway Bar Links: 25 Nm (18 ft-lb)
- Shock Absorber Bolts: 50 Nm (37 ft-lb)
Brake Bolt Torque Specifications
Technical procedure overview for brake bolt torque specifications on the Dodge dakota
- Caliper Bolts: 115 Nm (85 ft-lb)
- Rotor Bolts: 80 Nm (59 ft-lb)
- Master Cylinder Bolts: 25 Nm (18 ft-lb)
- Brake Line Fittings: 30 Nm (22 ft-lb)
Technical Service Bulletins
Driveline Vibration Technical Service Bulletin
2002-03-15Addresses excessive driveline vibration on certain models of the Dodge dakota. Includes updated torque specifications for driveshaft components.
1997-2001 dakota with 4.7L V8 engine and 4x4 drivetrain
Resolution: Inspect and tighten driveshaft bolts to the following specifications: Front driveshaft flange bolts: 100 Nm (74 ft-lb); Rear driveshaft flange bolts: 120 Nm (89 ft-lb).
Legal Disclaimer
Important information about using this content
Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.
General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability
The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.
We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.
Technical Information
- All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
- Vehicle specifications and procedures may vary by model year, trim level, and region.
- Always follow the manufacturer's recommended procedures and safety precautions.
- Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
- If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.
About the Author
Expert automotive knowledge and experience
'/%3E%3Cpath d='M60 30a20 20 0 1 1 0 40 20 20 0 0 1 0-40zm0 45c16.5 0 30 7.5 30 16.8V100H30v-8.2c0-9.3 13.5-16.8 30-16.8z' fill='%23404040'/%3E%3C/svg%3E)
ASE
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions
Diagnostic
Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.
Repair
Expert in both traditional mechanical repairs and modern vehicle systems.
Additional Expertise
Documentation
Created over 500 detailed repair guides and technical documents.
Training
Conducted technical training sessions and contributed to repair databases.
Certifications & Research
Certifications
- ASE Master Technician Certification
- Advanced Diagnostic Specialist
- Hybrid/Electric Vehicle Systems
- Performance Tuning Expert
Research & Community
Actively researches emerging technologies and contributes to automotive forums.