Dodge Charger 2011-present Torque Specifications
Dodge Charger 2011-present

Dodge Charger 2011-present Torque Specifications

Complete Dodge Charger 2011-present torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.

Updated

Important Information

Safety guidelines and reference information for proper torque application

Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083

Common Torque Patterns

Star Pattern

Used for wheels and other circular bolt patterns

Star Pattern torque pattern diagram showing proper bolt tightening sequence
Cross Pattern

Used for gaskets and cover plates

Cross Pattern torque pattern diagram showing proper bolt tightening sequence
Sequential Pattern

Used for head bolts and other critical components

Sequential Pattern torque pattern diagram showing proper bolt tightening sequence

Common Mistakes to Avoid

Over-tightening

Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.

Prevention:

Always use a calibrated torque wrench and follow specifications exactly.

Incorrect Torque Sequence

Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.

Prevention:

Follow the manufacturer's specified torque sequence pattern.

Dirty Threads

Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.

Prevention:

Clean and inspect all threads before assembly. Use new thread locker if specified.

Reusing TTY Bolts

Torque-to-yield bolts are designed to stretch and must not be reused.

Prevention:

Always replace TTY bolts with new ones. They are single-use only.

Dry vs. Lubricated

Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.

Prevention:

Check if specs are for dry or lubricated threads. Use specified lubricant when required.

Recommended Tools

Torque Wrench (1/4" Drive)

Range: 2-25 ft-lbs
Small fasteners, delicate components

Torque Wrench (3/8" Drive)

Range: 10-100 ft-lbs
Most common automotive fasteners

Torque Wrench (1/2" Drive)

Range: 30-250 ft-lbs
Large fasteners, wheels

Angle Gauge

Torque-to-yield (TTY) bolts

Torque Wrench Care

  • Calibrate annually or after 5,000 clicks
  • Store at lowest setting
  • Keep clean and lubricated

Search Specifications

Search by component name, bolt size, or description

Torque Calculator

Convert between different torque units

3.6l Engine

Torque specifications for 3.6L Engine

Cylinder Head

1

Cylinder Head Bolts

M10 x 1.5
Torque Specification
1. 15 ft-lbs (20 N·m) 2. 90°
Important Notes
Follow the specified torque sequence to ensure proper sealing. Values are based on typical M10 x 1.5 bolts.
2

Valve Cover Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure the valve cover gasket is properly seated before tightening.
3

Rocker Arms/Shafts Bolts

M8 x 1.25
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
Ensure proper alignment of rocker arms before tightening.

Crankshaft And Bearings

1

Main Bearing Bolts

M12 x 1.75
Torque Specification
105 ft-lbs (142 N·m)
Important Notes
Ensure proper alignment of main bearing caps before tightening.
2

Connecting Rod Nuts

M10 x 1.25
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Ensure proper alignment of connecting rods before tightening.
3

Flywheel Bolts

M12 x 1.75
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Ensure proper alignment of the flywheel before tightening.

Timing System

1

Timing Belt/Chain Tensioner Bolt

M8 x 1.25
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Ensure proper tension on the timing belt/chain before tightening.
2

Camshaft Sprocket Bolt

M10 x 1.25
Torque Specification
75 ft-lbs (102 N·m)
Important Notes
Ensure proper alignment of the camshaft sprocket before tightening.
3

Timing Cover Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure proper sealing of the timing cover before tightening.

Oil System

1

Oil Pan Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure proper sealing of the oil pan gasket before tightening.
2

Oil Filter Housing Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure proper sealing of the oil filter housing before tightening.
3

Oil Drain Plug Bolt

M14 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure proper sealing of the oil drain plug before tightening.

Intake And Exhaust

1

Intake Manifold Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure proper sealing of the intake manifold gasket before tightening.
2

Exhaust Manifold/Headers Bolts

M8 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure proper sealing of the exhaust manifold gasket before tightening.

Ignition And Fuel

1

Spark Plugs

M14 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure proper sealing and heat transfer for the spark plugs.
2

Ignition Coil Bolt

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure proper seating of the ignition coil before tightening.
3

Fuel Injector Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure proper sealing of the fuel injectors before tightening.

Cooling System

1

Water Pump Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure proper sealing of the water pump gasket before tightening.
2

Thermostat Housing Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure proper sealing of the thermostat housing gasket before tightening.

Accessory Drive

1

Alternator Mounting Bolts

M8 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure proper alignment of the alternator before tightening.
2

A/C Compressor Mounting Bolts

M8 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure proper alignment of the A/C compressor before tightening.
3

Power Steering Pump Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure proper alignment of the power steering pump before tightening.

5.7l Engine

Torque specifications for 5.7L Engine

Cylinder Head

1

Cylinder Head Bolts

M10 x 1.5
Torque Specification
1. 15 ft-lbs (20 N·m) 2. 90°
Important Notes
Follow the specified torque sequence to ensure proper sealing and prevent warping.
2

Rocker Arms/Shafts Bolts

M8 x 1.25
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
Ensure proper valve train alignment before tightening.
3

Valve Cover Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Use a crisscross pattern to ensure even sealing.

Crankshaft And Bearings

1

Main Bearing Bolts

M12 x 1.75
Torque Specification
105 ft-lbs (142 N·m)
Important Notes
Ensure proper alignment of the crankshaft before tightening.
2

Connecting Rod Nuts

M9 x 1.0
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Ensure proper piston and rod alignment before tightening.
3

Flywheel Bolts

M10 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Ensure the flywheel is properly seated on the crankshaft.

Timing System

1

Timing Chain Tensioner Bolt

M8 x 1.25
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Ensure proper tension on the timing chain before tightening.
2

Camshaft Sprocket Bolt

M12 x 1.75
Torque Specification
75 ft-lbs (102 N·m)
Important Notes
Ensure proper alignment of the camshaft sprocket.

Oil System

1

Oil Pan Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Use a crisscross pattern to ensure even sealing.
2

Oil Filter Housing Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure proper alignment of the oil filter housing.

Intake And Exhaust

1

Intake Manifold Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Use a crisscross pattern to ensure even sealing.
2

Exhaust Manifold/Headers Bolts

M8 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure proper alignment of the exhaust manifold.

6.2l Engine

Torque specifications for 6.2L Engine

Cylinder Head

1

Cylinder Head Bolts

M10 x 1.5
Torque Specification
1. 15 ft-lbs (20 N·m) 2. 90°
Important Notes
Follow the manufacturer's torque sequence to ensure even clamping force.
2

Rocker Arms/Shafts Bolts

M8 x 1.25
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
Ensure rocker arms are properly seated before tightening.

Crankshaft And Bearings

1

Main Bearing Bolts

M12 x 1.75
Torque Specification
105 ft-lbs (142 N·m)
Important Notes
Follow the manufacturer's torque sequence to ensure even clamping force.
2

Connecting Rod Nuts

M9 x 1.0
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Ensure connecting rods are properly seated before tightening.

Timing System

1

Camshaft Sprocket Bolt

M10 x 1.5
Torque Specification
75 ft-lbs (102 N·m)
Important Notes
Ensure the camshaft is properly aligned before tightening.
2

Timing Chain Tensioner Bolt

M8 x 1.25
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Ensure the tensioner is properly seated before tightening.

Oil System

1

Oil Pan Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Follow the manufacturer's torque sequence to ensure even clamping force.
2

Oil Drain Plug Bolt

M14 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure the drain plug gasket is in good condition before tightening.

Intake And Exhaust

1

Intake Manifold Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Follow the manufacturer's torque sequence to ensure even clamping force.
2

Exhaust Manifold/Headers Bolts

M8 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Follow the manufacturer's torque sequence to ensure even clamping force.

6.4l Engine

Torque specifications for 6.4L Engine

Cylinder Head

1

Cylinder Head Bolts

M10 x 1.5
Torque Specification
1. 15 ft-lbs (20 N·m) 2. 90°
Important Notes
Follow the manufacturer's specified torque sequence to ensure even clamping force.

Crankshaft And Bearings

1

Main Bearing Bolts

M12 x 1.75
Torque Specification
105 ft-lbs (142 N·m)
Important Notes
Ensure proper alignment of the main bearings before tightening.
2

Connecting Rod Nuts

M8 x 1.25
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Ensure proper alignment of the connecting rods before tightening.

Flywheel And Harmonic Balancer

1

Flywheel Bolts

M10 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Ensure the flywheel is properly aligned before tightening.
2

Crankshaft Pulley/Harmonic Balancer Bolt

M12 x 1.75
Torque Specification
130 ft-lbs (176 N·m)
Important Notes
Ensure the harmonic balancer is properly seated before tightening.

Oil System

1

Oil Pan Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure the oil pan gasket is properly seated before tightening.
2

Oil Filter Housing Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the oil filter housing is properly aligned before tightening.

Valvetrain

1

Rocker Arms/Shafts Bolts

M8 x 1.25
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
Ensure proper alignment of the rocker arms before tightening.
2

Valve Cover Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure the valve cover gasket is properly seated before tightening.

Timing System

1

Timing Chain Tensioner Bolt

M8 x 1.25
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Ensure the tensioner is properly seated before tightening.
2

Camshaft Sprocket Bolt

M10 x 1.5
Torque Specification
75 ft-lbs (102 N·m)
Important Notes
Ensure the camshaft sprocket is properly aligned before tightening.

Intake And Exhaust

1

Intake Manifold Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure the intake manifold gasket is properly seated before tightening.
2

Exhaust Manifold/Headers Bolts

M8 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure the exhaust manifold gasket is properly seated before tightening.

Cooling System

1

Water Pump Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure the water pump gasket is properly seated before tightening.
2

Thermostat Housing Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure the thermostat housing gasket is properly seated before tightening.

Ignition System

1

Spark Plugs

M14 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure the spark plugs are properly seated before tightening.

Fuel System

1

Fuel Rail Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure the fuel rail is properly aligned before tightening.
2

Fuel Injector Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure the fuel injectors are properly seated before tightening.

Accessories

1

Starter Motor Mounting Bolts

M8 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure the starter motor is properly aligned before tightening.
2

Alternator Mounting Bolts

M8 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure the alternator is properly aligned before tightening.
3

A/C Compressor Mounting Bolts

M8 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure the A/C compressor is properly aligned before tightening.
4

Power Steering Pump Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the power steering pump is properly aligned before tightening.

8hp70 Transmission

Torque specifications for 8hp70 Transmission

Transmission Mounting

1

Transmission Mounting Bolts

M10 x 1.5
Torque Specification
40 ft-lbs (54 N-m)
Important Notes
Ensure proper alignment of the transmission before tightening. Torque values are estimated based on similar components.

Oil Pan

1

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N-m)
Important Notes
Torque values are estimated based on similar components. Over-tightening can damage the oil pan gasket.

Fluid Plugs

1

Transmission Drain Plug

M12 x 1.75
Torque Specification
15 ft-lbs (20 N-m)
Important Notes
Torque values are estimated based on similar components. Use a new crush washer to ensure a proper seal.
2

Transmission Fill Plug

M12 x 1.75
Torque Specification
15 ft-lbs (20 N-m)
Important Notes
Torque values are estimated based on similar components. Use a new crush washer to ensure a proper seal.

Shaft Connections

1

Transmission Input Shaft Bolts

M12 x 1.5
Torque Specification
130 ft-lbs (176 N-m)
Important Notes
Torque values are estimated based on similar components. Ensure proper alignment of the input shaft before tightening.
2

Transmission Output Shaft Bolts

M14 x 1.5
Torque Specification
147 ft-lbs (200 N-m)
Important Notes
Torque values are estimated based on similar components. Ensure proper alignment of the output shaft before tightening.

Control Module

1

Transmission Control Module Bolts

M6 x 1.0
Torque Specification
18 ft-lbs (24 N-m)
Important Notes
Torque values are estimated based on similar components. Ensure proper alignment of the control module before tightening.

Shift Mechanism

1

Transmission Shift Lever Bolts

M8 x 1.25
Torque Specification
35 ft-lbs (47 N-m)
Important Notes
Torque values are estimated based on similar components. Ensure proper alignment of the shift lever before tightening.

8hp90 Transmission

Torque specifications for 8hp90 Transmission

Transmission Mounting

1

Transmission Mounting Bolts

M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure proper alignment of the transmission before tightening.

Oil Pan

1

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure the oil pan gasket is properly seated before tightening.

Fluid Plugs

1

Transmission Drain Plug

M12 x 1.5
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the plug is properly seated and the sealing washer is in good condition.
2

Transmission Fill Plug

M12 x 1.5
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the plug is properly seated and the sealing washer is in good condition.

Drive Axle

1

Drive Axle/Half Shaft Bolts

M12 x 1.5
Torque Specification
147 ft-lbs (200 N·m)
Important Notes
Ensure the axle is properly seated before tightening.
2

CV Joint/Axle Nut

M24 x 1.5
Torque Specification
147 ft-lbs (200 N·m)
Important Notes
Ensure the axle is properly seated before tightening.

Propeller Shaft

1

Propeller/Drive Shaft Bolts

M10 x 1.5
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Ensure the drive shaft is properly aligned before tightening.

Torque Converter

1

Torque Converter Bolts

M8 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure the torque converter is properly seated before tightening.

Bellhousing

1

Transmission Bellhousing Bolts

M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the bellhousing is properly aligned with the engine block.

Valve Body

1

Transmission Valve Body Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure the valve body is properly seated before tightening.
2

Transmission Solenoid Pack Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure the solenoid pack is properly seated before tightening.

Output Shaft

1

Transmission Output Shaft Flange Bolts

M10 x 1.5
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Ensure the output shaft flange is properly seated before tightening.

Cooler Lines

1

Transmission Cooler Line Fittings

M12 x 1.5
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the cooler lines are properly seated before tightening.

Body

Torque specifications for Body

Suspension And Steering

1

Wheel Lug Nuts

M12 x 1.5
Torque Specification
110 ft-lbs (149 N·m)
Important Notes
Critical for safety and wheel alignment. Torque in a star pattern.
2

Strut/Shock Absorber Mounting Bolts

M12 x 1.5
Torque Specification
100 ft-lbs (136 N·m)
Important Notes
Ensures proper suspension operation and structural integrity.
3

Control Arm Bolts

M12 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Ensures alignment and stability of the suspension system.
4

Ball Joint Nut

M12 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Ensures safe and precise steering.
5

Tie Rod End Nut

M10 x 1.25
Torque Specification
55 ft-lbs (75 N·m)
Important Notes
Ensures accurate steering response.
6

Sway Bar Link Nut

M10 x 1.25
Torque Specification
55 ft-lbs (75 N·m)
Important Notes
Reduces body roll and improves handling.
7

Steering Gear/Rack Bolts

M12 x 1.5
Torque Specification
100 ft-lbs (136 N·m)
Important Notes
Ensures proper steering operation and alignment.

Fuel System

1

Fuel Tank Strap Bolts

M8 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensures the fuel tank remains stable and properly positioned.
2

Fuel Filler Neck Bolts

M8 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensures a proper seal and prevents fuel leaks.

Electrical System

1

Battery Terminal Nuts

M6 x 1.0
Torque Specification
5.9 ft-lbs (8 N·m)
Important Notes
Ensures a reliable electrical connection and prevents corrosion.

Body Panels

1

Body Panel Bolts (e.g., fender, door, hood, trunk)

M6 x 1.0
Torque Specification
17.5 ft-lbs (23.5 N·m)
Important Notes
Estimated value. Ensures panels remain securely fastened without warping.
2

Seat Belt Anchorage Bolts

M10 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Estimated value. Ensures passenger safety in the event of a collision.
3

Seat Mounting Bolts

M10 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Estimated value. Ensures seats remain stable and safe during operation.
4

Radiator Support Bolts

M6 x 1.0
Torque Specification
17.5 ft-lbs (23.5 N·m)
Important Notes
Estimated value. Ensures proper alignment and stability of the cooling system components.
5

Bumper Mounting Bolts

M6 x 1.0
Torque Specification
17.5 ft-lbs (23.5 N·m)
Important Notes
Estimated value. Ensures bumpers remain properly aligned and stable.
6

Door Hinge Bolts

M6 x 1.0
Torque Specification
17.5 ft-lbs (23.5 N·m)
Important Notes
Estimated value. Ensures proper alignment and operation of the doors.
7

Hood Hinge Bolts

M6 x 1.0
Torque Specification
17.5 ft-lbs (23.5 N·m)
Important Notes
Estimated value. Ensures proper alignment and operation of the hood.
8

Trunk Lid Hinge Bolts

M6 x 1.0
Torque Specification
17.5 ft-lbs (23.5 N·m)
Important Notes
Estimated value. Ensures proper alignment and operation of the trunk.

Brakes

Torque specifications for Brakes

Brake Caliper System

1

Brake Caliper Bolts

M12 x 1.5
Torque Specification
130 ft-lbs (176 N·m)
Important Notes
Ensure caliper is properly aligned before torquing.
2

Brake Caliper Mounting Bracket Bolts

M12 x 1.5
Torque Specification
130 ft-lbs (176 N·m)
Important Notes
Ensure bracket is seated properly before torquing.

Brake Rotor Drum System

1

Brake Disc/Drum Retaining Bolts

M10 x 1.25
Torque Specification
100 ft-lbs (136 N·m)
Important Notes
Ensure rotor/drum is seated properly on the hub before torquing.

Brake Hydraulic System

1

Brake Hose Banjo Bolt

M10 x 1.0
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
Estimated value. Ensure sealing washers are properly seated.
2

Brake Master Cylinder Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value. Ensure master cylinder is properly aligned.

Brake Booster Pedal System

1

Brake Booster Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value. Ensure booster is properly aligned.
2

Brake Pedal Assembly Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value. Ensure pedal operates smoothly after installation.

Abs System

1

ABS Module Mounting Bolts

M6 x 1.0
Torque Specification
12 ft-lbs (16 N·m)
Important Notes
Estimated value. Ensure module is properly aligned.

Wheel Attachment System

1

Wheel Lug Nuts

M12 x 1.5
Torque Specification
110 ft-lbs (149 N·m)
Important Notes
Use a star pattern for even torque distribution.

Drivetrain

Torque specifications for Drivetrain

Flywheel

1

Flywheel Bolts

M12 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Ensure the flywheel is properly aligned before tightening.

Transmission

1

Transmission Mounting Bolts

M10 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the transmission is properly aligned before tightening.
2

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Use a crisscross pattern to ensure even sealing.
3

Transmission Drain and Fill Plugs

M12 x 1.5
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the sealing washer is in good condition.
4

Transmission Bellhousing Bolts

M10 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Estimated value based on similar components.

Driveshaft

1

Propeller/Drive Shaft Bolts

M10 x 1.25
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Ensure the driveshaft is properly aligned before tightening.

Differential

1

Drive Axle/Half Shaft Bolts

M14 x 1.5
Torque Specification
147 ft-lbs (200 N·m)
Important Notes
Ensure the axle is properly seated before tightening.
2

Differential Drain/Fill Plug

M12 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Ensure the sealing washer is in good condition.
3

Differential Mounting Bolts

M12 x 1.75
Torque Specification
75 ft-lbs (102 N·m)
Important Notes
Estimated value based on similar components.

Transfer Case

1

Transfer Case Drain/Fill Plug

M12 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Ensure the sealing washer is in good condition.
2

Transfer Case Mounting Bolts

M10 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Estimated value based on similar components.

Cv Joint

1

CV Joint/Axle Nut

M24 x 1.5
Torque Specification
147 ft-lbs (200 N·m)
Important Notes
Ensure the axle is properly seated before tightening.

Transmission Crossmember

1

Transmission Crossmember Bolts

M10 x 1.25
Torque Specification
50 ft-lbs (68 N·m)
Important Notes
Estimated value based on similar components.

Electrical

Torque specifications for Electrical

Ignition System

1

Ignition Coil Bolt

M10 x 1.25
Torque Specification
9 ft-lbs (12 N-m)
Important Notes
Estimated bolt size based on typical ignition coil bolts. Ensure proper torque to prevent arcing or misfires.
2

Starter Motor Mounting Bolt

M12 x 1.5
Torque Specification
35 ft-lbs (47 N-m)
Important Notes
Estimated bolt size based on typical starter motor bolts. Ensure proper torque to prevent misalignment.

Charging System

1

Alternator Mounting Bolt

M12 x 1.5
Torque Specification
35 ft-lbs (47 N-m)
Important Notes
Estimated bolt size based on typical alternator bolts. Ensure proper torque for correct alignment with the drive belt.
2

Battery Terminal Nut

M8 x 1.25
Torque Specification
6 ft-lbs (8 N-m)
Important Notes
Estimated bolt size based on typical battery terminal nuts. Ensure proper torque to prevent voltage drops.

Grounding System

1

Ground Strap Bolt

M8 x 1.25
Torque Specification
10 ft-lbs (14 N-m)
Important Notes
Estimated bolt size based on typical ground strap bolts. Ensure proper torque for reliable grounding.

Power Distribution

1

Fuse Box Mounting Bolt

M10 x 1.25
Torque Specification
9 ft-lbs (12 N-m)
Important Notes
Estimated bolt size based on typical fuse box bolts. Ensure proper torque to prevent vibration damage.
2

Wiring Harness Clamp Bolt

M10 x 1.25
Torque Specification
9 ft-lbs (12 N-m)
Important Notes
Estimated bolt size based on typical wiring harness clamp bolts. Ensure proper torque to prevent chafing.

Engine Control

1

ECU/ECM Mounting Bolt

M10 x 1.25
Torque Specification
9 ft-lbs (12 N-m)
Important Notes
Estimated bolt size based on typical ECU/ECM bolts. Ensure proper torque to prevent vibration damage.

Lighting System

1

Headlight Housing Bolt

M10 x 1.25
Torque Specification
9 ft-lbs (12 N-m)
Important Notes
Estimated bolt size based on typical headlight housing bolts. Ensure proper torque to prevent vibration damage.

Emissions Sensors

Torque specifications for Emissions_sensors

Egr System

1

EGR Valve Bolts

M8 x 1.25
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Ensure the EGR valve is properly aligned before tightening.
2

EGR Cooler Bolts

M10 x 1.5
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value based on similar components. Ensure proper alignment and sealing.

Exhaust Manifold

1

Exhaust Manifold/Headers Bolts

M10 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Use a crisscross pattern to ensure even pressure.
2

Exhaust Manifold/Headers to Cylinder Head Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure proper alignment and sealing.

Exhaust Pipe

1

Exhaust Pipe to Exhaust Manifold/Headers Bolts

M10 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Use a crisscross pattern to ensure even pressure.
2

Catalytic Converter to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure proper alignment and sealing.

Oxygen Sensors

1

Oxygen Sensor (O2 Sensor)

M18 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Estimated value based on similar components. Ensure proper alignment and sealing.

Diesel Emissions

1

DPF (Diesel Particulate Filter) Mounting Bolts

M10 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Estimated value based on similar components. Ensure proper alignment and sealing.

Exhaust

Torque specifications for Exhaust

Exhaust Manifold Headers

1

Exhaust Manifold/Headers Bolts

M10 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to evenly distribute pressure.
2

Exhaust Manifold/Headers to Cylinder Head Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to evenly distribute pressure.

Exhaust Pipe Connections

1

Exhaust Pipe to Exhaust Manifold/Headers Bolts

M10 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure gasket is properly seated before tightening.
2

Catalytic Converter to Exhaust Pipe Bolts

M10 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure gasket is properly seated before tightening.
3

Muffler to Exhaust Pipe Bolts

M10 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure gasket is properly seated before tightening.
4

Exhaust Flange Bolts (Mid-Pipe to Rear Pipe)

M10 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure gasket is properly seated before tightening.

Exhaust Support Components

1

Exhaust Hanger Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value based on typical M8 bolt torque specifications.
2

Oxygen Sensor (O2 Sensor) Bolts

M12 x 1.25
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
Estimated value based on typical M12 bolt torque specifications.
3

Exhaust Heat Shield Bolts

M6 x 1.0
Torque Specification
12 ft-lbs (16 N·m)
Important Notes
Estimated value based on typical M6 bolt torque specifications.

Fuel

Torque specifications for Fuel

Fuel Rail System

1

Fuel Rail Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure proper torque to prevent fuel leaks. Torque sequence is critical for even pressure distribution.
2

Fuel Injector Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Proper torque ensures a secure seal for the injectors. Torque sequence is critical.

Fuel Pump And Tank System

1

Fuel Pump Mounting Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure proper torque to prevent fuel leaks and secure the fuel pump.
2

Fuel Tank Strap Bolts

M10 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Proper torque ensures the fuel tank is securely mounted.
3

Fuel Filler Neck Bolts

M10 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Proper torque ensures a tight seal to prevent fuel vapor leaks.
4

Fuel Tank Sender Unit Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Proper torque ensures a tight seal and accurate fuel level readings.

Fuel Filter And Lines

1

Fuel Filter Bolt/Nut

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Proper torque ensures the filter is tightly sealed.
2

High-Pressure Fuel Line Fittings

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Proper torque ensures a secure connection for high-pressure fuel lines.
3

Fuel Line Clamp Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Proper torque ensures fuel lines are securely held in place.

Fuel Pressure Regulator

1

Fuel Pressure Regulator Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Proper torque ensures a secure seal and prevents fuel leaks.

Hvac

Torque specifications for Hvac

Ac Compressor

1

A/C Compressor Mounting Bolts

M10 x 1.25
Torque Specification
35 ft-lbs (47 N-m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to evenly distribute load.
2

A/C Line Fittings

M8 x 1.25
Torque Specification
18 ft-lbs (24 N-m)
Important Notes
Ensure fittings are clean and free of debris before installation.

Evaporator Housing

1

Evaporator Housing Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N-m)
Important Notes
Tighten bolts in a crisscross pattern to ensure even sealing pressure.

Blower Motor

1

Blower Motor Mounting Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N-m)
Important Notes
Ensure the blower motor is properly aligned before tightening.

Heater Core

1

Heater Core Inlet/Outlet Fittings

M8 x 1.25
Torque Specification
15 ft-lbs (20 N-m)
Important Notes
Ensure fittings are clean and free of debris before installation.

Suspension

Torque specifications for Suspension

Strut Shock Absorber

1

Strut/Shock Absorber Mounting Bolts

M12 x 1.5
Torque Specification
100 ft-lbs (136 N·m)
Important Notes
Ensure bolts are tightened evenly to prevent misalignment.
2

Lower Strut Mount Bolts

M12 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Estimated value based on similar suspension components.
3

Upper Strut Mount Bolts

M10 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Estimated value based on similar suspension components.

Control Arm Ball Joint

1

Control Arm Bolts

M12 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Ensure bolts are tightened evenly to prevent misalignment.
2

Ball Joint Nut

M12 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Ensure the ball joint is properly seated before tightening.

Steering System

1

Tie Rod End Nut

M10 x 1.25
Torque Specification
55 ft-lbs (75 N·m)
Important Notes
Ensure the tie rod end is properly seated before tightening.
2

Steering Gear/Rack Bolts

M12 x 1.5
Torque Specification
100 ft-lbs (136 N·m)
Important Notes
Ensure bolts are tightened evenly to prevent misalignment.

Sway Bar System

1

Sway Bar Link Nut

M10 x 1.25
Torque Specification
55 ft-lbs (75 N·m)
Important Notes
Ensure the sway bar link is properly seated before tightening.
2

Rear Sway Bar Mounting Bolts

M8 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Estimated value based on similar suspension components.

Wheel Hub System

1

Wheel Lug Nuts

M12 x 1.5
Torque Specification
1. 110 ft-lbs (149 N·m)
Important Notes
Always use a crisscross pattern when tightening wheel lug nuts.

Subframe System

1

Subframe Mounting Bolts

M14 x 1.5
Torque Specification
1. 125 ft-lbs (170 N·m)
Important Notes
Estimated value based on similar suspension components.

Rear Suspension System

1

Rear Suspension Trailing Arm Bolts

M12 x 1.5
Torque Specification
90 ft-lbs (122 N·m)
Important Notes
Estimated value based on similar suspension components.

W5a580 Transmission

Torque specifications for W5a580 Transmission

Transmission Mounting

1

Transmission Mounting Bolts

M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure proper alignment of the transmission before tightening.

Oil Pan

1

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Use a new gasket and ensure the pan surface is clean before installation.

Fluid Management

1

Transmission Drain Plug

M12 x 1.5
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the plug is properly seated to prevent leaks.
2

Transmission Fill Plug

M12 x 1.5
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the plug is properly seated to prevent leaks.
3

Transmission Cooler Line Fittings

M14 x 1.5
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure proper alignment of the cooler lines to prevent leaks.

Drivetrain Connection

1

Drive Axle/Half Shaft Bolts

M12 x 1.5
Torque Specification
147 ft-lbs (200 N·m)
Important Notes
Ensure proper alignment of the axle before tightening.
2

CV Joint/Axle Nut

M24 x 1.5
Torque Specification
147 ft-lbs (200 N·m)
Important Notes
Ensure the axle is properly seated before tightening.
3

Propeller/Drive Shaft Bolts

M10 x 1.25
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Ensure proper alignment of the drive shaft before tightening.

Starter Motor

1

Starter Motor Mounting Bolts

M8 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure proper alignment of the starter motor before tightening.

Torque Converter

1

Torque Converter Bolts

M8 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure proper alignment of the torque converter before tightening.

Bellhousing

1

Transmission Bellhousing Bolts

M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure proper alignment of the bellhousing before tightening.

Valve Body

1

Transmission Valve Body Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure proper alignment of the valve body before tightening.
2

Transmission Solenoid Pack Bolts

M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure proper alignment of the solenoid pack before tightening.

Shift Linkage

1

Transmission Shift Linkage Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure proper alignment of the shift linkage before tightening.

Troubleshooting Guide

Common issues, diagnostic steps, and prevention guidelines

Common Issues

Bolt stretching, stripped threads, uneven torque patterns

Loose Components

Symptoms:
  • Rattling or vibration noises
  • Visible movement in components
  • Uneven panel gaps
Solutions:
  • Clean threads and mounting surfaces
  • Replace damaged fasteners
  • Apply proper torque in sequence
  • Use thread locker if specified

Stripped Fasteners

Symptoms:
  • Unable to achieve proper torque
  • Fastener spins freely
  • Visible thread damage
Solutions:
  • Use thread repair kit if appropriate
  • Install thread insert (HeliCoil)
  • Replace component if threaded hole is damaged
  • Upgrade to higher grade fastener if recommended

Overtightened Components

Symptoms:
  • Cracked or deformed parts
  • Broken fasteners
  • Compressed gaskets or seals
Solutions:
  • Replace damaged components
  • Use new fasteners
  • Follow proper torque sequence
  • Verify correct torque specifications

Diagnostic Steps

Visual inspection, torque verification, thread assessment

1

Visual Inspection

Inspect the affected area for any visible signs of damage or wear

  • Check for cracks or deformation
  • Look for signs of excessive wear
  • Verify proper fastener installation
2

Torque Verification

Verify the torque applied to the fasteners

  • Check the torque wrench calibration
  • Verify the torque specification
  • Compare the applied torque to the specification
3

Thread Assessment

Assess the condition of the threads

  • Check for signs of thread damage
  • Verify the thread type and size
  • Check for proper thread engagement

Prevention Guidelines

Best practices, maintenance tips, tool care

Best Practices

  • Always follow the recommended torque specification
  • Use the correct type and size of fasteners
  • Verify the torque wrench calibration regularly

Maintenance Tips

  • Regularly inspect the affected area for signs of wear or damage
  • Replace damaged or worn-out components promptly
  • Keep the work area clean and organized

Tool Care

  • Regularly clean and maintain the torque wrench
  • Store the torque wrench in a dry and secure location
  • Verify the torque wrench calibration before each use

Frequently Asked Questions

Find answers to common questions about torque specifications

Q1

What are the torque specifications for the lug nuts on a 2011-Present Dodge Charger?

110 ft-lbs (150 Nm)

Q2

What IS the torque specification for the spark plugs on a 2011-Present Dodge Charger?

18 ft-lbs (25 Nm) for 3.6L engine, 30 ft-lbs (41 Nm) for 5.7L and 6.4L engines

Q3

What IS the torque specification for the oil filter on a 2011-Present Dodge Charger?

25 ft-lbs (34 Nm)

Q4

What tools do I need to measure torque accurately?

A torque wrench IS essential for accurate torque measurements. Choose a torque wrench that IS calibrated to the correct range for the bolts you are tightening.

Q5

How often should I re-torque bolts?

You should re-torque bolts only when they have been loosened or removed. Over-tightening bolts can damage them or the components they are securing.

Q6

What are the consequences of incorrect torque application?

Incorrect torque application can cause bolts to become loose, which can lead to component failure. Over-tightening bolts can damage them or the components they are securing.

Environmental Considerations

Temperature, humidity, and seasonal effects on torque specifications

Temperature Effects

Includes: High Heat, Cold Weather, Thermal Cycling

Temperature can significantly impact torque values and fastener behavior

Cold Weather

Effects:
  • Increased material brittleness
  • Higher torque required due to thread contraction
  • Reduced thread lubricant effectiveness
Recommendations:
  • Allow components to warm to room temperature when possible
  • Consider using winter-grade thread lubricants
  • Check torque values more frequently during winter months

Hot Weather

Effects:
  • Thermal expansion of components
  • Decreased friction in threads
  • Accelerated lubricant breakdown
Recommendations:
  • Check torque when components are at normal operating temperature
  • Use temperature-resistant thread lockers
  • Consider re-torquing after heat cycles

Humidity and Corrosion

Covers: Rust Prevention, Salt Exposure, Moisture Control

Moisture and corrosion can affect fastener integrity and torque values

High Humidity

Effects:
  • Accelerated corrosion formation
  • Reduced friction coefficient
  • Potential thread seizing
Prevention:
  • Use corrosion-resistant fasteners
  • Apply appropriate anti-seize compounds
  • Maintain proper protective coatings

Salt Exposure

Effects:
  • Rapid corrosion development
  • Thread damage
  • Seized fasteners
Prevention:
  • Regular underbody washing
  • Use of sacrificial anodes where appropriate
  • Application of protective coatings

Seasonal Maintenance

Spring, Summer, Fall, and Winter maintenance schedules

Spring

  • Inspect for winter damage
  • Clean and protect exposed fasteners
  • Check torque on critical components

Summer

  • Monitor heat-affected components
  • Check expansion-related loosening
  • Inspect cooling system mounts

Fall

  • Prepare for winter conditions
  • Apply corrosion protection
  • Verify all fasteners are properly torqued

Winter

  • More frequent inspection of critical fasteners
  • Check for salt damage
  • Monitor suspension component torque

Related Resources

Tools, service procedures, and technical bulletins

Recommended Tools

Digital Torque Wrench (10-100 Nm)

Essential for tightening bolts to precise torque specifications, preventing damage and ensuring proper assembly. This range IS suitable for many applications on the 2011-Present Dodge charger

  • Digital display for accurate readings
  • Audible alarm when target torque IS reached
  • Multiple units (Nm, ft-lb, in-lb)
  • Reversible ratcheting mechanism
Learn more
Service Procedures
Technical Service Bulletins

Legal Disclaimer

Important information about using this content

Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.

General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability

The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.

We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.

Technical Information
  • All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
  • Vehicle specifications and procedures may vary by model year, trim level, and region.
  • Always follow the manufacturer's recommended procedures and safety precautions.
  • Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
  • If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.

About the Author

Expert automotive knowledge and experience

Alan Montanye - Automotive Technical Specialist
ASE

Alan Montanye

Automotive Technical Specialist

ASE Master Certified Technician with over a decade of hands-on experience in automotive repair and diagnostics.

Facebook Contact
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions

Diagnostic

Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.

Repair

Expert in both traditional mechanical repairs and modern vehicle systems.

Additional Expertise

Documentation

Created over 500 detailed repair guides and technical documents.

Training

Conducted technical training sessions and contributed to repair databases.

Certifications & Research

Certifications

  • ASE Master Technician Certification
  • Advanced Diagnostic Specialist
  • Hybrid/Electric Vehicle Systems
  • Performance Tuning Expert

Research & Community

Actively researches emerging technologies and contributes to automotive forums.

© 2025 Dodge Specs. All rights reserved.

Privacy Policy Terms of Service