Dodge Caliber 2007-2012
Dodge Caliber 2007-2012 Torque Specifications
Complete Dodge Caliber 2007-2012 torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.
Updated
Important Information
Safety guidelines and reference information for proper torque application
Safety First
- Always verify torque specifications with your vehicle's factory service manual
- Use properly calibrated torque wrenches
- Replace all torque-to-yield (TTY) bolts - they are single-use only
- When in doubt, consult a professional mechanic
Quick Reference Guide
Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083
Common Torque Patterns
Star Pattern
Used for wheels and other circular bolt patterns
Cross Pattern
Used for gaskets and cover plates
Sequential Pattern
Used for head bolts and other critical components
Common Mistakes to Avoid
Common Mistakes to Avoid
Over-tightening
Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.
Prevention:
Always use a calibrated torque wrench and follow specifications exactly.
Incorrect Torque Sequence
Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.
Prevention:
Follow the manufacturer's specified torque sequence pattern.
Dirty Threads
Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.
Prevention:
Clean and inspect all threads before assembly. Use new thread locker if specified.
Reusing TTY Bolts
Torque-to-yield bolts are designed to stretch and must not be reused.
Prevention:
Always replace TTY bolts with new ones. They are single-use only.
Dry vs. Lubricated
Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.
Prevention:
Check if specs are for dry or lubricated threads. Use specified lubricant when required.
Recommended Tools
Recommended Tools
Torque Wrench (1/4" Drive)
Range: 2-25 ft-lbs
Small fasteners, delicate components
Torque Wrench (3/8" Drive)
Range: 10-100 ft-lbs
Most common automotive fasteners
Torque Wrench (1/2" Drive)
Range: 30-250 ft-lbs
Large fasteners, wheels
Angle Gauge
Torque-to-yield (TTY) bolts
Torque Wrench Care
- Calibrate annually or after 5,000 clicks
- Store at lowest setting
- Keep clean and lubricated
Search Specifications
Search by component name, bolt size, or description
Type to search through torque specifications. Use arrow keys to navigate results. Press Enter to select a result.
Torque Calculator
Convert between different torque units
1.8l Engine
Torque specifications for 1.8L Engine
1.8l Engine
Torque specifications for 1.8L Engine
Cylinder Head
1 Cylinder Head Bolts
M10 x 1.5
1
Cylinder Head Bolts
M10 x 1.5
Torque Specification
1. 18 ft-lbs (24 N·m)
2. 90°
3. 90°
Important Notes
Cylinder head bolts require a multi-step torque procedure, including initial torque and two angular tightening steps. Refer to the specific service manual for the correct tightening sequence.
2 Camshaft Bearing Cap Bolts
M8 x 1.25
2
Camshaft Bearing Cap Bolts
M8 x 1.25
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensures proper camshaft alignment and prevents damage. Estimated value; verify with the specific service manual.
3 Rocker Arms/Shafts Bolts
M8 x 1.25
3
Rocker Arms/Shafts Bolts
M8 x 1.25
Torque Specification
21 ft-lbs (28 N·m)
Important Notes
Secures the rocker arm assembly to the cylinder head. These are crucial for proper valve actuation.
4 Valve Cover Bolts
M6 x 1.0
4
Valve Cover Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Secures the valve cover to the cylinder head, preventing oil leaks. Over-torquing can damage the valve cover.
5 Ignition Coil Bolt
M6 x 1.0
5
Ignition Coil Bolt
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Secures the ignition coils to the valve cover. These bolts must be snug to ensure proper electrical connection.
Engine Block
1 Main Bearing Bolts
M12 x 1.75
1
Main Bearing Bolts
M12 x 1.75
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Secures the main bearing caps to the engine block. Correct torque is essential for proper crankshaft alignment and bearing function.
2 Connecting Rod Nuts
M9 x 1.25
2
Connecting Rod Nuts
M9 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Secures the connecting rod to the crankshaft journal. Proper torque is vital for proper rod bearing function and preventing rod failure.
3 Oil Pan Bolts
M6 x 1.0
3
Oil Pan Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Secures the oil pan to the bottom of the engine block. Over-torquing can crush the oil pan gasket.
4 Oil Drain Plug Bolt
M14 x 1.5
4
Oil Drain Plug Bolt
M14 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Secures the oil drain plug to the oil pan. Use a new washer when installing.
5 Crankshaft Position Sensor (CKP) Bolt
M6 x 1.0
5
Crankshaft Position Sensor (CKP) Bolt
M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Secures the CKP sensor to the engine block or cylinder head. Estimated value, verify with the specific service manual.
6 Water Pump Bolts
M6 x 1.0
6
Water Pump Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Secures the water pump to the engine block. Prevents coolant leaks.
Rotating Assembly
1 Flywheel Bolts
M10 x 1.5
1
Flywheel Bolts
M10 x 1.5
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Attaches the flywheel (manual trans.) or flexplate (automatic trans.) to the crankshaft. Apply thread locker to the bolts.
2 Crankshaft Pulley/Harmonic Balancer Bolt
M14 x 1.5
2
Crankshaft Pulley/Harmonic Balancer Bolt
M14 x 1.5
Torque Specification
105 ft-lbs (142 N·m)
Important Notes
Secures the crankshaft pulley and harmonic balancer to the crankshaft. This bolt is critical for driving the accessory drive belt and maintaining engine balance.
Timing System
1 Timing Belt/Chain Tensioner Bolt
M8 x 1.25
1
Timing Belt/Chain Tensioner Bolt
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Secures the timing belt/chain tensioner. Proper torque is critical for maintaining correct valve timing.
2 Camshaft Sprocket Bolt
M10 x 1.25
2
Camshaft Sprocket Bolt
M10 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Secures the camshaft sprockets to the camshafts. This is important for maintaining precise valve timing.
Intake System
1 Throttle Body Bolts
M6 x 1.0
1
Throttle Body Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Attaches the throttle body to the intake manifold. This connection must be airtight to prevent vacuum leaks.
2 Intake Manifold Bolts
M6 x 1.0
2
Intake Manifold Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Secures the intake manifold to the cylinder head. A proper seal is necessary to maintain the correct air/fuel mixture and to prevent vacuum leaks.
3 EGR Valve Bolts
M6 x 1.0
3
EGR Valve Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Secures the EGR valve to the intake manifold/cylinder head. Prevents exhaust gas leaks from the system.
Exhaust System
1 Exhaust Manifold/Headers Bolts
M8 x 1.25
1
Exhaust Manifold/Headers Bolts
M8 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Secures the exhaust manifold to the cylinder head. A proper torque is vital to prevent exhaust leaks.
Fuel System
1 Fuel Rail Bolts
M6 x 1.0
1
Fuel Rail Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Secures the fuel rail to the intake manifold. This is vital for preventing fuel leaks and maintaining the correct fuel pressure.
2 Fuel Injector Bolts
M6 x 1.0
2
Fuel Injector Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Secures the fuel injectors to the fuel rail. Prevents fuel leaks and maintains correct fuel injection.
Cooling System
1 Water Pump Pulley Bolts
M6 x 1.0
1
Water Pump Pulley Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Secures the water pump pulley to the water pump. This is important for proper drive belt function and water pump operation.
2 Thermostat Housing Bolts
M6 x 1.0
2
Thermostat Housing Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Secures the thermostat housing to the cylinder head/engine block. Prevents coolant leaks and ensures correct temperature regulation.
Misc
1 Spark Plugs
M14 x 1.25
1
Spark Plugs
M14 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Secures the spark plugs into the cylinder head. Proper torque ensures a good electrical and thermal contact and prevents leaks from the cylinder.
2 Oil Filter Housing Bolt
M20 x 1.5
2
Oil Filter Housing Bolt
M20 x 1.5
Torque Specification
N/A
Important Notes
Secures the oil filter housing. It should be hand-tight to avoid over tightening.
2.0l Engine
Torque specifications for 2.0L Engine
2.0l Engine
Torque specifications for 2.0L Engine
Cylinder Head
1 Cylinder Head Bolts
M10 x 1.5
1
Cylinder Head Bolts
M10 x 1.5
Torque Specification
1. 18 ft-lbs (24 N·m)
Important Notes
Use a three-step tightening sequence (e.g., 1/3 final torque, 2/3 final, then full torque in sequence) and follow a cross pattern. Always use new bolts.
2 Valve Cover Bolts
M6 x 1.0
2
Valve Cover Bolts
M6 x 1.0
Torque Specification
7.9 ft-lbs (11 N·m)
Important Notes
Tighten the valve cover bolts in a criss-cross pattern, and be careful not to overtighten. This value is converted from 95 in-lbs
3 Rocker Arms/Shafts Bolts
M8 x 1.25
3
Rocker Arms/Shafts Bolts
M8 x 1.25
Torque Specification
21 ft-lbs (28 N·m)
Important Notes
Tighten these bolts in a sequence that evenly applies pressure to the rocker arm assembly.
4 Camshaft Sprocket Bolt
M10 x 1.25
4
Camshaft Sprocket Bolt
M10 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the camshaft sprocket is properly aligned before tightening. If applicable, use a camshaft holding tool.
Engine Block
1 Main Bearing Bolts
M12 x 1.5
1
Main Bearing Bolts
M12 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Main bearing bolts must be torqued to the correct specification. It is advised to use new bolts and tighten in sequence to ensure even bearing cap pressure.
2 Connecting Rod Nuts
M8 x 1.0
2
Connecting Rod Nuts
M8 x 1.0
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure that the connecting rod caps are installed in the correct direction. Using new fasteners is recommended. Tighten each rod cap in a two-step process.
3 Oil Pan Bolts
M6 x 1.0
3
Oil Pan Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten oil pan bolts in a criss-cross pattern, and be careful not to overtighten. This value is converted from 105 in-lbs
4 Oil Drain Plug Bolt
M14 x 1.5
4
Oil Drain Plug Bolt
M14 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Always use a new sealing washer when installing the oil drain plug to prevent leaks. Do not over torque.
Timing System
1 Timing Belt/Chain Tensioner Bolt
M8 x 1.25
1
Timing Belt/Chain Tensioner Bolt
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure that the tensioner is properly positioned before tightening. Check the manufacturer's specifications for correct tension.
2 Timing Cover Bolts
M6 x 1.0
2
Timing Cover Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten in a criss-cross pattern for even pressure, and be careful not to overtighten. This value is converted from 105 in-lbs
Intake Exhaust
1 Intake Manifold Bolts
M6 x 1.0
1
Intake Manifold Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten intake manifold bolts in a criss-cross pattern, and be careful not to overtighten. This value is converted from 105 in-lbs
2 Exhaust Manifold/Headers Bolts
M8 x 1.25
2
Exhaust Manifold/Headers Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Tighten the exhaust manifold bolts using a proper torque sequence to ensure an even seal, and avoid leaks.
3 Throttle Body Bolts
M6 x 1.0
3
Throttle Body Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten in a criss-cross pattern for even pressure. This value is converted from 105 in-lbs
4 EGR Valve Bolts
M6 x 1.0
4
EGR Valve Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten evenly to prevent leaks. This value is converted from 105 in-lbs
Fuel System
1 Fuel Rail Bolts
M6 x 1.0
1
Fuel Rail Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten the fuel rail bolts evenly to ensure proper seal. This value is converted from 105 in-lbs
2 Fuel Injector Bolts
M6 x 1.0
2
Fuel Injector Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten evenly to prevent fuel leaks. This value is converted from 105 in-lbs
Ignition System
1 Spark Plugs
M14 x 1.25
1
Spark Plugs
M14 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure that the threads are clean and correctly installed before torque.
2 Ignition Coil Bolts
M6 x 1.0
2
Ignition Coil Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten the bolts evenly to ensure proper coil grounding. This value is converted from 105 in-lbs
Cooling System
1 Water Pump Bolts
M6 x 1.0
1
Water Pump Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten the bolts evenly in a criss-cross pattern to prevent leaks. This value is converted from 105 in-lbs
2 Water Pump Pulley Bolts
M6 x 1.0
2
Water Pump Pulley Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten the bolts evenly. This value is converted from 105 in-lbs
3 Thermostat Housing Bolts
M6 x 1.0
3
Thermostat Housing Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten the bolts evenly, and be careful not to over tighten, use a new gasket. This value is converted from 105 in-lbs
4 Coolant Temperature Sensor Bolt
M6 x 1.0
4
Coolant Temperature Sensor Bolt
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten the sensor evenly. This value is converted from 105 in-lbs. Sensor may have a sealing washer.
5 Coolant Outlet Housing Bolts
M6 x 1.0
5
Coolant Outlet Housing Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten the bolts evenly and use a new gasket. This value is converted from 105 in-lbs.
Accessory Drive
1 Crankshaft Pulley/Harmonic Balancer Bolt
M14 x 1.5
1
Crankshaft Pulley/Harmonic Balancer Bolt
M14 x 1.5
Torque Specification
105 ft-lbs (142 N·m)
Important Notes
Ensure proper alignment of the crankshaft pulley/harmonic balancer before tightening.
2 Serpentine/Accessory Drive Belt Tensioner Bolt
M8 x 1.25
2
Serpentine/Accessory Drive Belt Tensioner Bolt
M8 x 1.25
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure the tensioner is properly positioned. This value is converted from 105 in-lbs
3 Drive Belt Idler Pulley Bolt
M10 x 1.5
3
Drive Belt Idler Pulley Bolt
M10 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure the idler pulley is properly aligned, and does not bind before tightening.
Sensors
1 Crankshaft Position Sensor (CKP) Bolt
M6 x 1.0
1
Crankshaft Position Sensor (CKP) Bolt
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten the sensor bolt evenly, and be careful not to over tighten. This value is converted from 105 in-lbs
2 Camshaft Position Sensor (CMP) Bolt
M6 x 1.0
2
Camshaft Position Sensor (CMP) Bolt
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten the sensor bolt evenly. This value is converted from 105 in-lbs
3 Knock Sensor Bolt
M8 x 1.25
3
Knock Sensor Bolt
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Tighten sensor to the specified torque to ensure correct sensor operation.
Starter Charging Ac
1 Starter Motor Mounting Bolts
M10 x 1.5
1
Starter Motor Mounting Bolts
M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure that the starter is seated correctly before tightening.
2 Alternator Mounting Bolts
M10 x 1.5
2
Alternator Mounting Bolts
M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure that the alternator is properly aligned before tightening.
3 A/C Compressor Mounting Bolts
M10 x 1.5
3
A/C Compressor Mounting Bolts
M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the A/C compressor is properly positioned before tightening.
Other
1 Flywheel Bolts
M10 x 1.25
1
Flywheel Bolts
M10 x 1.25
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
It is recommended to use new bolts and tighten in sequence.
2 Oil Filter Housing Bolt
M8 x 1.25
2
Oil Filter Housing Bolt
M8 x 1.25
Torque Specification
N/A
Important Notes
Tighten by hand only. Do not overtighten.
2.4l Engine
Torque specifications for 2.4L Engine
2.4l Engine
Torque specifications for 2.4L Engine
Cylinder Head
1 Cylinder Head Bolts
M11 x 1.5
1
Cylinder Head Bolts
M11 x 1.5
Torque Specification
1. 18 ft-lbs (24 N·m)
2. 90°
3. 90°
Important Notes
Tighten bolts in the correct sequence. Torque to 18 ft-lbs (24 Nm), then tighten an additional 90 degrees, then an additional 90 degrees.
2 Cylinder Head Oil Gallery Plug
M10 x 1.25
2
Cylinder Head Oil Gallery Plug
M10 x 1.25
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Estimated value. Ensure plug sealing surface is clean.
3 Rocker Arms/Shafts Bolts
M8 x 1.25
3
Rocker Arms/Shafts Bolts
M8 x 1.25
Torque Specification
21 ft-lbs (28 N·m)
Important Notes
Tighten bolts evenly to ensure proper rocker arm function.
4 Camshaft Bearing Cap Bolts
M6 x 1.0
4
Camshaft Bearing Cap Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Estimated value. Tighten evenly in sequence to avoid camshaft distortion.
Engine Block
1 Main Bearing Bolts
M12 x 1.75
1
Main Bearing Bolts
M12 x 1.75
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Ensure proper main bearing alignment. Tighten in sequence.
2 Oil Pan Bolts
M6 x 1.0
2
Oil Pan Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Tighten in a criss-cross pattern to avoid leaks.
3 Oil Drain Plug
M14 x 1.5
3
Oil Drain Plug
M14 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Use a new sealing washer each time.
4 Water Pump Bolts
M8 x 1.25
4
Water Pump Bolts
M8 x 1.25
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Tighten evenly to ensure proper seal.
5 Crankshaft Position Sensor Bolt
M6 x 1.0
5
Crankshaft Position Sensor Bolt
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Estimated value. Ensure sensor is properly positioned.
6 Knock Sensor
M8 x 1.25
6
Knock Sensor
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure proper sensor contact and avoid overtightening.
Crankshaft And Connecting Rods
1 Connecting Rod Nuts
M9 x 1.0
1
Connecting Rod Nuts
M9 x 1.0
Torque Specification
1. 20 ft-lbs (27 N·m)
2. 60°
Important Notes
Tighten in the correct sequence. Torque to 20 ft-lbs (27 Nm), then tighten an additional 60 degrees.
2 Flywheel Bolts
M10 x 1.5
2
Flywheel Bolts
M10 x 1.5
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Tighten in a star pattern.
3 Crankshaft Pulley/Harmonic Balancer Bolt
M14 x 1.5
3
Crankshaft Pulley/Harmonic Balancer Bolt
M14 x 1.5
Torque Specification
105 ft-lbs (142 N·m)
Important Notes
Ensure pulley is seated correctly.
Timing System
1 Timing Belt/Chain Tensioner Bolt
M8 x 1.25
1
Timing Belt/Chain Tensioner Bolt
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure correct tensioner operation.
2 Camshaft Sprocket Bolt
M10 x 1.25
2
Camshaft Sprocket Bolt
M10 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure proper sprocket alignment.
Intake And Exhaust
1 Intake Manifold Bolts
M6 x 1.0
1
Intake Manifold Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Tighten in a criss-cross pattern.
2 Throttle Body Bolts
M6 x 1.0
2
Throttle Body Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Tighten evenly to prevent air leaks.
3 Exhaust Manifold/Headers Bolts
M8 x 1.25
3
Exhaust Manifold/Headers Bolts
M8 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Tighten in a sequence starting from the center out.
4 EGR Valve Bolts
M6 x 1.0
4
EGR Valve Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure proper sealing between the valve and manifold.
Fuel System
1 Fuel Rail Bolts
M6 x 1.0
1
Fuel Rail Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure fuel rail is properly positioned.
2 Fuel Injector Bolts
M6 x 1.0
2
Fuel Injector Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure injector is properly seated.
Ignition System
1 Spark Plugs
M14 x 1.25
1
Spark Plugs
M14 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Use a torque wrench for correct compression sealing.
2 Ignition Coil Bolt
M6 x 1.0
2
Ignition Coil Bolt
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure coil is properly seated and secured.
Cooling System
1 Water Pump Pulley Bolts
M6 x 1.0
1
Water Pump Pulley Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure pulley is properly aligned.
2 Thermostat Housing Bolts
M6 x 1.0
2
Thermostat Housing Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure proper sealing to prevent coolant leaks.
3 Coolant Temperature Sensor
M10 x 1.0
3
Coolant Temperature Sensor
M10 x 1.0
Torque Specification
13 ft-lbs (18 N·m)
Important Notes
Estimated value. Avoid overtightening, ensure sensor seals properly.
Accessories
1 Serpentine/Accessory Drive Belt Tensioner Bolt
M8 x 1.25
1
Serpentine/Accessory Drive Belt Tensioner Bolt
M8 x 1.25
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure tensioner is correctly aligned and secured.
Valve Cover
1 Valve Cover Bolts
M6 x 1.0
1
Valve Cover Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten bolts evenly to avoid warping and leaks
2 Camshaft Position Sensor Bolt
M6 x 1.0
2
Camshaft Position Sensor Bolt
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Estimated value. Ensure sensor is properly positioned.
Body
Torque specifications for Body
Body
Torque specifications for Body
Hood Assembly
1 Hood Hinge Bolts
M8 x 1.25
1
Hood Hinge Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure hood is aligned before final torque. Estimated value; consult specific manual for exact spec.
2 Hood Hinge Bolts
M10 x 1.5
2
Hood Hinge Bolts
M10 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Ensure hood is aligned before final torque. Estimated value; consult specific manual for exact spec.
3 Hood Latch Bolts
M6 x 1.0
3
Hood Latch Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure hood latch is properly aligned for secure closure. Estimated value; consult specific manual for exact spec.
Exterior Panels
1 Fender Bolts
M6 x 1.0
1
Fender Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Install all bolts loosely before final torquing. Estimated value; consult specific manual for exact spec.
2 Fender Bolts
M8 x 1.25
2
Fender Bolts
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Install all bolts loosely before final torquing. Estimated value; consult specific manual for exact spec.
3 Bumper Cover Mounting Bolts/Fasteners
M6 x 1.0
3
Bumper Cover Mounting Bolts/Fasteners
M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Do not overtighten to prevent damage to the bumper cover. Estimated value; consult specific manual for exact spec.
Door Assembly
1 Door Hinge Bolts
M8 x 1.25
1
Door Hinge Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure proper door alignment before final torque. Estimated value; consult specific manual for exact spec.
2 Door Hinge Bolts
M10 x 1.5
2
Door Hinge Bolts
M10 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Ensure proper door alignment before final torque. Estimated value; consult specific manual for exact spec.
3 Door Latch Striker Bolts
M6 x 1.0
3
Door Latch Striker Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Adjust striker position for smooth door closure. Estimated value; consult specific manual for exact spec.
4 Door Latch Striker Bolts
M8 x 1.25
4
Door Latch Striker Bolts
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Adjust striker position for smooth door closure. Estimated value; consult specific manual for exact spec.
Lighting
1 Headlight Mounting Bolts
M6 x 1.0
1
Headlight Mounting Bolts
M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Do not overtighten. Ensure proper headlight alignment. Estimated value; consult specific manual for exact spec.
2 Tail Light Mounting Bolts
M6 x 1.0
2
Tail Light Mounting Bolts
M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Do not overtighten. Ensure proper tail light alignment. Estimated value; consult specific manual for exact spec.
Grille
1 Grille Mounting Bolts/Screws
M6 x 1.0
1
Grille Mounting Bolts/Screws
M6 x 1.0
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Do not overtighten. Estimated value; consult specific manual for exact spec.
Rear Hatch
1 Rear Hatch/Liftgate Strut Bolts
M8 x 1.25
1
Rear Hatch/Liftgate Strut Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the struts are properly aligned. Estimated value; consult specific manual for exact spec.
Interior
1 Seat Mounting Bolts
M8 x 1.25
1
Seat Mounting Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the seats are correctly positioned before final torque. Estimated value; consult specific manual for exact spec.
2 Seat Mounting Bolts
M10 x 1.5
2
Seat Mounting Bolts
M10 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Ensure the seats are correctly positioned before final torque. Estimated value; consult specific manual for exact spec.
3 Seat Belt Mounting Bolts
M8 x 1.25
3
Seat Belt Mounting Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Critical for safety; ensure proper installation. Estimated value; consult specific manual for exact spec.
4 Seat Belt Mounting Bolts
M10 x 1.5
4
Seat Belt Mounting Bolts
M10 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Critical for safety; ensure proper installation. Estimated value; consult specific manual for exact spec.
5 Dashboard Mounting Bolts
M6 x 1.0
5
Dashboard Mounting Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Do not overtighten to avoid cracking the dashboard. Estimated value; consult specific manual for exact spec.
6 Dashboard Mounting Bolts
M8 x 1.25
6
Dashboard Mounting Bolts
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Do not overtighten to avoid cracking the dashboard. Estimated value; consult specific manual for exact spec.
7 Interior Trim Panel Screws/Bolts
M4 x 0.7
7
Interior Trim Panel Screws/Bolts
M4 x 0.7
Torque Specification
3 ft-lbs (4 N·m)
Important Notes
Hand tight plus a slight turn. Do not overtighten. Estimated value; consult specific manual for exact spec.
8 Interior Trim Panel Screws/Bolts
M5 x 0.8
8
Interior Trim Panel Screws/Bolts
M5 x 0.8
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Hand tight plus a slight turn. Do not overtighten. Estimated value; consult specific manual for exact spec.
Brakes
Torque specifications for Brakes
Brakes
Torque specifications for Brakes
Caliper Assembly
1 Caliper Slide Bolts
M10 x 1.5
1
Caliper Slide Bolts
M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
These bolts secure the caliper body to the caliper bracket, allowing the caliper to slide for proper brake engagement. Ensure the slide pins are lubricated with silicone based caliper grease prior to installation. Always replace bolts if they are worn or damaged.
2 Caliper Mounting Bracket Bolts
M12 x 1.75
2
Caliper Mounting Bracket Bolts
M12 x 1.75
Torque Specification
80 ft-lbs (108 N·m)
Important Notes
These bolts attach the caliper mounting bracket to the steering knuckle. Use a cross pattern when tightening to ensure even clamping force. Always replace bolts if they are worn or damaged.
3 Brake Pad Guide Pin Bolts
M8 x 1.25
3
Brake Pad Guide Pin Bolts
M8 x 1.25
Torque Specification
13 ft-lbs (17 N·m)
Important Notes
These bolts secure the brake pad retaining pins which guide the brake pads and allow them to move freely within the caliper. Ensure that the pins and bolts are lubricated using a silicone based caliper grease. Always replace bolts if they are worn or damaged.
Rotor And Hub
1 Brake Rotor Retaining Bolts
M8 x 1.25
1
Brake Rotor Retaining Bolts
M8 x 1.25
Torque Specification
100 ft-lbs (136 N·m)
Important Notes
These bolts secure the brake rotor to the wheel hub. They are essential for concentric rotor rotation. Note: These may be temporary bolts used only for assembly and not meant for final mounting with wheel attached. Always replace bolts if they are worn or damaged.
Hydraulic System
1 Brake Line Banjo Bolt
M10 x 1.0
1
Brake Line Banjo Bolt
M10 x 1.0
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
This bolt secures the brake line to the caliper. Always use new crush washers on both sides of the banjo fitting. Over-torquing can damage the seals and cause leaks, under-torquing can cause leaks as well.
2 Brake Master Cylinder Mounting Nuts
M8 x 1.25
2
Brake Master Cylinder Mounting Nuts
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
These nuts secure the master cylinder to the brake booster. Ensure the master cylinder is properly seated against the booster before tightening. Use a cross pattern when tightening to ensure even clamping force. Always replace nuts if they are worn or damaged.
3 Brake Booster Mounting Nuts
M8 x 1.25
3
Brake Booster Mounting Nuts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
These nuts secure the brake booster to the firewall. Ensure the booster is properly seated before tightening. Use a cross pattern when tightening to ensure even clamping force. Always replace nuts if they are worn or damaged.
Abs System
1 Wheel Speed Sensor Mounting Bolts
M6 x 1.0
1
Wheel Speed Sensor Mounting Bolts
M6 x 1.0
Torque Specification
6 in-lbs (8 N·m)
Important Notes
These bolts secure the wheel speed sensors to the steering knuckle. Ensuring proper torque prevents sensor damage and malfunction, essential for proper ABS operation. Use a calibrated in-lb torque wrench for accuracy. Always replace bolts if they are worn or damaged.
Drivetrain
Torque specifications for Drivetrain
Drivetrain
Torque specifications for Drivetrain
Engine Flywheel
1 Flywheel Bolts
M12 x 1.25
1
Flywheel Bolts
M12 x 1.25
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Ensure bolts are clean and lightly lubricated before installation. Tighten in a star pattern.
2 Clutch Pressure Plate Bolts
M8 x 1.25
2
Clutch Pressure Plate Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Tighten pressure plate bolts in a star pattern. Estimated value based on common M8 bolt size.
Transmission Mounting
1 Transmission Mounting Bolts
M12 x 1.75
1
Transmission Mounting Bolts
M12 x 1.75
Torque Specification
55 ft-lbs (75 N·m)
Important Notes
Ensure proper alignment before tightening. Bolts should be clean and threads in good condition.
2 Transmission Case Bolts
M10 x 1.5
2
Transmission Case Bolts
M10 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Tighten case bolts in a criss-cross pattern for even clamping. Estimated value based on common M10 bolt size.
3 Transmission Oil Pan Bolts
M6 x 1.0
3
Transmission Oil Pan Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Tighten bolts in a criss-cross pattern to ensure even gasket compression. Avoid over-tightening, which can cause leaks. Value converted from in-lbs.
Transmission Service
1 Transmission Drain and Fill Plugs
M18 x 1.5
1
Transmission Drain and Fill Plugs
M18 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Use new crush washers if equipped, avoid overtightening to prevent damage to the case.
Driveshaft Axles
1 Drive Axle/Half Shaft Bolts
M10 x 1.25
1
Drive Axle/Half Shaft Bolts
M10 x 1.25
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Ensure proper alignment of the CV joint flange. Use thread locker if recommended.
2 CV Joint/Axle Nut
M24 x 1.5
2
CV Joint/Axle Nut
M24 x 1.5
Torque Specification
180 ft-lbs (244 N·m)
Important Notes
Use a new nut, as most CV axle nuts are single-use. Torque to specification to ensure proper wheel bearing preload and then stake/crimp.
3 Propeller/Drive Shaft Bolts
M10 x 1.5
3
Propeller/Drive Shaft Bolts
M10 x 1.5
Torque Specification
75 ft-lbs (102 N·m)
Important Notes
Tighten in a star pattern. Ensure proper alignment of the driveshaft flanges.
4 Driveshaft Center Support Bearing Bolts
M8 x 1.25
4
Driveshaft Center Support Bearing Bolts
M8 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure proper alignment of the bearing before tightening. Estimated value based on typical M8 bolt size.
Differential
1 Differential Drain/Fill Plug
M18 x 1.5
1
Differential Drain/Fill Plug
M18 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Use a new crush washer if equipped. Do not overtighten.
2 Differential Cover Bolts
M10 x 1.5
2
Differential Cover Bolts
M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Tighten bolts in a criss-cross pattern for even gasket compression. Estimated value based on common M10 bolt size.
Transfer Case
1 Transfer Case Drain/Fill Plug
M18 x 1.5
1
Transfer Case Drain/Fill Plug
M18 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Use a new crush washer if equipped. Do not overtighten.
Electrical
Torque specifications for Electrical
Electrical
Torque specifications for Electrical
Ignition System
1 Ignition Coil Mounting Bolt
M6 x 1.0
1
Ignition Coil Mounting Bolt
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensures proper coil grounding and secure placement. Over-tightening may damage the coil housing or threads.
2 Crankshaft Position Sensor Mounting Bolt
M6 x 1.0
2
Crankshaft Position Sensor Mounting Bolt
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensures secure sensor mounting to read crankshaft position properly, and provides a proper ground. Over-tightening can damage the sensor or threads.
3 Camshaft Position Sensor Mounting Bolt
M6 x 1.0
3
Camshaft Position Sensor Mounting Bolt
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensures secure mounting of the sensor to read camshaft position properly, and provides a proper ground. Over-tightening can damage the sensor or threads.
Starting Charging System
1 Starter Motor Mounting Bolt
M10 x 1.5
1
Starter Motor Mounting Bolt
M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensures proper alignment of the starter motor and good electrical contact with the engine block for proper grounding. Over-tightening may damage the starter mounting surface or threads.
2 Alternator Mounting Bolt
M10 x 1.5
2
Alternator Mounting Bolt
M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensures proper alignment of the alternator and secure grounding to the engine block or mounting bracket. Over-tightening may damage the alternator housing or mounting surface.
3 Battery Terminal Nut
M6 x 1.0
3
Battery Terminal Nut
M6 x 1.0
Torque Specification
6.6 ft-lbs (9 N·m)
Important Notes
Ensures a secure connection for the battery cables and proper electrical contact with the battery terminals. Over-tightening can damage the battery posts, while under-tightening can cause poor conductivity and arcing.
Powertrain Control
1 Engine Control Module (ECM) / Powertrain Control Module (PCM) Mounting Bolt
M6 x 1.0
1
Engine Control Module (ECM) / Powertrain Control Module (PCM) Mounting Bolt
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensures proper grounding and secure mounting for the ECM/PCM. Over-tightening can damage the module housing or threads. Sometimes mounted with clips or screws, but some are secured with bolts.
2 Manifold Absolute Pressure (MAP) Sensor Mounting Bolt
M5 x 0.8
2
Manifold Absolute Pressure (MAP) Sensor Mounting Bolt
M5 x 0.8
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensures secure mounting and grounding for the MAP sensor. Over-tightening may damage the sensor or threads.
3 Mass Airflow (MAF) Sensor Mounting Bolt
M5 x 0.8
3
Mass Airflow (MAF) Sensor Mounting Bolt
M5 x 0.8
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensures secure mounting and grounding for the MAF sensor. Over-tightening may damage the sensor or threads.
Body Control
1 Body Control Module (BCM) Mounting Bolt
M6 x 1.0
1
Body Control Module (BCM) Mounting Bolt
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensures proper grounding of the module. Over-tightening can damage the module housing or threads. Sometimes mounted with clips or screws, but some are secured with bolts.
2 Headlamp Mounting Bolt
M5 x 0.8
2
Headlamp Mounting Bolt
M5 x 0.8
Torque Specification
6.6 ft-lbs (9 N·m)
Important Notes
Ensures secure mounting of the headlamp to the body. Over-tightening may damage the headlamp housing or threads. Good electrical contact between the lamp assembly and the chassis is important.
3 Taillight Mounting Bolt
M5 x 0.8
3
Taillight Mounting Bolt
M5 x 0.8
Torque Specification
6.6 ft-lbs (9 N·m)
Important Notes
Ensures secure mounting of the taillight assembly. Over-tightening may damage the taillight housing or threads. Good electrical contact between the lamp assembly and the chassis is important.
Electrical Distribution
1 Fuse Box Mounting Bolt
M6 x 1.0
1
Fuse Box Mounting Bolt
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensures proper grounding and secure mounting of the fuse box. Over-tightening may damage the fuse box housing or threads.
2 Ground Strap/Wire Connection Bolt
M6 x 1.0
2
Ground Strap/Wire Connection Bolt
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensures a secure and low-resistance connection for ground straps and wires. Clean and free of corrosion for proper electrical performance. Over-tightening may damage threads or connection hardware. Value is estimated.
Emissions Sensors
Torque specifications for Emissions_sensors
Emissions Sensors
Torque specifications for Emissions_sensors
Exhaust System
1 Exhaust Manifold to Cylinder Head
M8 x 1.25
1
Exhaust Manifold to Cylinder Head
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Tighten bolts in a crisscross pattern, starting from the center and working outwards. Always use a torque wrench and ensure clean, undamaged threads. Improper torque will cause warping, leaking and inaccurate readings of the upstream O2 Sensor
2 Exhaust Manifold/Headers to Exhaust Pipe
M10 x 1.5
2
Exhaust Manifold/Headers to Exhaust Pipe
M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure a proper seal at the flange. Use new gaskets when replacing components. Improper torque will cause leaks and inaccurate readings from the O2 sensor.
3 Catalytic Converter to Exhaust Pipe
M10 x 1.5
3
Catalytic Converter to Exhaust Pipe
M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure proper flange alignment and a new gasket is used. Improper torque can cause leaks which would impact the downstream oxygen sensor. The joint here will experience high heat and vibration, so ensure proper tightening is done.
4 Oxygen (O2) Sensor Mounting Studs/Nuts
M8 x 1.25 (Studs) / M8 (Nuts)
4
Oxygen (O2) Sensor Mounting Studs/Nuts
M8 x 1.25 (Studs) / M8 (Nuts)
Torque Specification
32 ft-lbs (43 N·m)
Important Notes
Apply anti-seize compound to the threads to prevent seizing. Ensure proper engagement of threads. Do not overtighten. An estimate has been used as specific torque may depend on the specific type of mounting
Intake System
1 EGR Valve
M6 x 1.0
1
EGR Valve
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Use a new gasket and tighten bolts evenly. Ensure the valve is properly seated. Improper torque can lead to leaks and poor engine performance.
2 Mass Air Flow (MAF) Sensor
M5 x 0.8
2
Mass Air Flow (MAF) Sensor
M5 x 0.8
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Do not overtighten. Ensure the sensor is properly seated. Improper torque or over tightening could damage plastic housing. This value is estimated, as the plastic MAF can be damaged by overtightening.
3 Manifold Absolute Pressure (MAP) Sensor
M5 x 0.8
3
Manifold Absolute Pressure (MAP) Sensor
M5 x 0.8
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Do not overtighten. Ensure the sensor is properly seated. Improper torque can damage the plastic sensor body, or create a leak. This value is estimated, as the plastic MAP can be damaged by overtightening.
Fuel System
1 Fuel Injector Bolts
M6 x 1.0
1
Fuel Injector Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Use new O-rings and ensure proper seating of the injectors. Improper torque can lead to fuel leaks and incorrect sensor readings.
Exhaust
Torque specifications for Exhaust
Exhaust
Torque specifications for Exhaust
Exhaust Manifold Headers
1 Exhaust Manifold/Headers to Engine Block Bolts
M12 x 1.5
1
Exhaust Manifold/Headers to Engine Block Bolts
M12 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
2 Exhaust Manifold/Headers to Cylinder Head Bolts
M10 x 1.25
2
Exhaust Manifold/Headers to Cylinder Head Bolts
M10 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Exhaust Pipe
1 Exhaust Pipe to Exhaust Manifold/Headers Bolts
M12 x 1.5
1
Exhaust Pipe to Exhaust Manifold/Headers Bolts
M12 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
2 Muffler to Exhaust Pipe Bolts
M14 x 1.75
2
Muffler to Exhaust Pipe Bolts
M14 x 1.75
Torque Specification
35 ft-lbs (47 N·m)
Catalytic Converter
1 Catalytic Converter to Exhaust Pipe Bolts
M12 x 1.5
1
Catalytic Converter to Exhaust Pipe Bolts
M12 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Oxygen Sensor
1 Oxygen Sensor Bolts
M8 x 1.25
1
Oxygen Sensor Bolts
M8 x 1.25
Torque Specification
22.5 ft-lbs (30.5 N·m)
Important Notes
Estimated value, consult manufacturer's recommendations for accurate information.
Exhaust System Mounting
1 Exhaust System Mounting Bolts
M10 x 1.5
1
Exhaust System Mounting Bolts
M10 x 1.5
Torque Specification
25 ft-lbs (33.9 N·m)
Important Notes
Estimated value, consult manufacturer's recommendations for accurate information.
Heat Shield
1 Heat Shield Bolts
M6 x 1.0
1
Heat Shield Bolts
M6 x 1.0
Torque Specification
12.5 ft-lbs (16.9 N·m)
Important Notes
Estimated value, consult manufacturer's recommendations for accurate information.
Fuel
Torque specifications for Fuel
Fuel
Torque specifications for Fuel
Fuel Rail
1 Fuel Rail Mounting Bolts
M6 x 1.0
1
Fuel Rail Mounting Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Tighten bolts in a cross pattern to ensure even pressure.
2 Fuel Injector Mounting Bolts
M6 x 1.0
2
Fuel Injector Mounting Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure injector O-rings are properly seated before tightening.
3 Fuel Line Fitting at Fuel Rail (Banjo Bolt)
M12 x 1.5
3
Fuel Line Fitting at Fuel Rail (Banjo Bolt)
M12 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
This is an estimated value. Always check manufacturer’s specifications when available. Use new sealing washers.
4 Fuel Pressure Regulator Mounting Bolts
M6 x 1.0
4
Fuel Pressure Regulator Mounting Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
This is an estimated value. Ensure regulator O-ring is in good condition.
Fuel Delivery
1 Fuel Pump Module Mounting Bolts
M6 x 1.0
1
Fuel Pump Module Mounting Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure the fuel pump module is correctly seated in the tank.
2 Fuel Filter Mounting Bolt/Nut
M8 x 1.25
2
Fuel Filter Mounting Bolt/Nut
M8 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure filter bracket is properly aligned before tightening.
3 Fuel Line Fitting at Fuel Filter (Banjo Bolt)
M10 x 1.25
3
Fuel Line Fitting at Fuel Filter (Banjo Bolt)
M10 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
This is an estimated value. Always use new sealing washers.
Fuel Tank
1 Fuel Tank Sending Unit/Lock Ring
N/A
1
Fuel Tank Sending Unit/Lock Ring
N/A
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Torque specification is for the lock ring. If the lock ring has alignment marks, use those as a guide, if not, use this torque value. Use a lock ring tool if applicable.
2 Fuel Tank Vent Valve Mounting Bolts
M6 x 1.0
2
Fuel Tank Vent Valve Mounting Bolts
M6 x 1.0
Torque Specification
6 ft-lbs (9 N·m)
Important Notes
This is an estimated value. Ensure the vent valve seal is in good condition.
Hvac
Torque specifications for Hvac
Hvac
Torque specifications for Hvac
Ac Compressor
1 A/C Compressor Mounting Bolts
M10 x 1.5
1
A/C Compressor Mounting Bolts
M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure bolts are clean and lightly lubricated with anti-seize if specified. Tighten evenly to avoid stressing the compressor housing.
2 A/C Line Fittings
Varies, typically 1/2 - 20 UNF
2
A/C Line Fittings
Varies, typically 1/2 - 20 UNF
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Use a flare nut wrench to avoid rounding the fitting. Ensure O-rings are properly seated and lubricated with refrigerant oil. Do not over-tighten to prevent leaks or damage to the fittings.
Ac Condenser
1 A/C Condenser Mounting Bolts/Nuts
M6 x 1.0
1
A/C Condenser Mounting Bolts/Nuts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Estimated value. Ensure bolts are snug but do not over-tighten to avoid damaging the condenser fins. Use caution when tightening, as condenser mounting points are typically quite thin.
Ac Evaporator
1 A/C Evaporator Housing/Box Mounting Bolts/Nuts
M5 x 0.8
1
A/C Evaporator Housing/Box Mounting Bolts/Nuts
M5 x 0.8
Torque Specification
6.6 ft-lbs (9 N·m)
Important Notes
Estimated value. Do not over-tighten the bolts to prevent damage to the housing. Ensure proper alignment to avoid leaks and rattles.
2 A/C Expansion Valve Mounting Bolts/Screws
M5 x 0.8
2
A/C Expansion Valve Mounting Bolts/Screws
M5 x 0.8
Torque Specification
6.6 ft-lbs (9 N·m)
Important Notes
Estimated value. Tighten evenly to avoid stressing the valve body. Ensure sealing washers are properly installed to prevent leaks.
Blower Motor
1 Blower Motor Mounting Bolts/Screws
M4 x 0.7
1
Blower Motor Mounting Bolts/Screws
M4 x 0.7
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Estimated value. Ensure the blower motor is flush with the housing before tightening. Do not over-tighten the screws to prevent damage to the plastic housing.
Hvac Controls
1 HVAC Control Module Mounting Screws
M4 x 0.7
1
HVAC Control Module Mounting Screws
M4 x 0.7
Torque Specification
1.6 ft-lbs (2.25 N·m)
Important Notes
Estimated value. Be very careful not to over-tighten; plastic housings and circuit boards are easily damaged. Tighten just enough to secure the module.
Jf011e Transmission
Torque specifications for Jf011e Transmission
Jf011e Transmission
Torque specifications for Jf011e Transmission
Transmission Mounting
1 Transmission Mounting Bolts
M14 x 1.5
1
Transmission Mounting Bolts
M14 x 1.5
Torque Specification
55 ft-lbs (75 N�m)
Important Notes
These bolts secure the transmission to the engine block and transmission crossmember, ensuring proper alignment and preventing movement or vibration that could affect transmission performance.
Transmission Oil Pan
1 Transmission Oil Pan Bolts
M10 x 1.25
1
Transmission Oil Pan Bolts
M10 x 1.25
Torque Specification
10 ft-lbs (12 N�m)
Important Notes
These bolts secure the oil pan to the transmission case, preventing oil leaks and ensuring the transmission is properly lubricated.
Transmission Fluid System
1 Transmission Drain and Fill Plugs
M12 x 1.5
1
Transmission Drain and Fill Plugs
M12 x 1.5
Torque Specification
20 ft-lbs (27 N�m)
Important Notes
These plugs allow for the draining and filling of transmission fluid, and proper torque ensures a leak-free seal.
2 Transmission Fluid Drain/Fill Plug
M12 x 1.5
2
Transmission Fluid Drain/Fill Plug
M12 x 1.5
Torque Specification
20 ft-lbs (27 N�m)
Important Notes
This plug is specific to the transmission fluid system and requires proper torque to prevent leaks and ensure the transmission is properly serviced.
Transmission Case
1 Transmission Case Bolts
M14 x 1.5
1
Transmission Case Bolts
M14 x 1.5
Torque Specification
40 ft-lbs (54 N�m)
Important Notes
These bolts secure the transmission case halves together and are critical for maintaining the transmission's internal pressure and preventing leaks. The recommended torque value is based on industry standards for similar transmission designs.
Transmission Bellhousing
1 Transmission Bellhousing Bolts
M12 x 1.5
1
Transmission Bellhousing Bolts
M12 x 1.5
Torque Specification
30 ft-lbs (40 N�m)
Important Notes
These bolts secure the bellhousing to the transmission case and engine block, ensuring proper alignment and preventing movement or vibration that could affect transmission performance. The recommended torque value is based on industry standards for similar transmission designs.
Transmission Cooler Lines
1 Transmission Cooler Line Fittings
M10 x 1.25
1
Transmission Cooler Line Fittings
M10 x 1.25
Torque Specification
15 ft-lbs (20 N�m)
Important Notes
These fittings connect the transmission cooler lines to the transmission case and radiator, and proper torque ensures a leak-free seal. The recommended torque value is based on industry standards for similar transmission designs.
Suspension
Torque specifications for Suspension
Suspension
Torque specifications for Suspension
Front Suspension
1 Strut Assembly to Steering Knuckle Bolts
M14 x 1.5
1
Strut Assembly to Steering Knuckle Bolts
M14 x 1.5
Torque Specification
100 ft-lbs (135 N·m)
Important Notes
Tighten bolts in a criss-cross pattern to ensure even clamping force. Final torque should be achieved in one smooth pull.
2 Strut Mount to Body Bolts
M10 x 1.25
2
Strut Mount to Body Bolts
M10 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure the strut mount is properly seated before tightening. Do not overtighten.
3 Lower Control Arm Ball Joint to Steering Knuckle Nut
M12 x 1.75
3
Lower Control Arm Ball Joint to Steering Knuckle Nut
M12 x 1.75
Torque Specification
55 ft-lbs (75 N·m)
Important Notes
Ensure the ball joint stud is properly seated in the knuckle before tightening. Use a new nut if specified.
4 Lower Control Arm to Frame Bolts
M14 x 2.0
4
Lower Control Arm to Frame Bolts
M14 x 2.0
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Tighten bolts in a specified order (usually inner first, then outer). Final torque should be achieved in one smooth pull.
5 Sway Bar End Link to Strut Bolt
M10 x 1.5
5
Sway Bar End Link to Strut Bolt
M10 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Hold the end link stud with a wrench while tightening to avoid rotation. Do not overtighten.
6 Sway Bar Frame Mount Bolts
M8 x 1.25
6
Sway Bar Frame Mount Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the bushings are correctly seated before tightening. Do not overtighten, it will cause bushing damage.
Rear Suspension
1 Rear Shock Absorber Upper Mount Bolts
M10 x 1.5
1
Rear Shock Absorber Upper Mount Bolts
M10 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Ensure the shock mount is aligned properly before tightening. Do not overtighten, as damage to mounting studs could occur.
2 Rear Shock Absorber Lower Mount Bolt
M12 x 1.75
2
Rear Shock Absorber Lower Mount Bolt
M12 x 1.75
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Ensure the shock is properly seated in the mount before tightening. Use a new nut if specified.
3 Upper Control Arm to Frame Bolts
M12 x 1.75
3
Upper Control Arm to Frame Bolts
M12 x 1.75
Torque Specification
70 ft-lbs (95 N·m)
Important Notes
Tighten bolts in a criss-cross pattern to ensure even clamping force.
4 Lower Control Arm to Frame Bolts
M14 x 2.0
4
Lower Control Arm to Frame Bolts
M14 x 2.0
Torque Specification
95 ft-lbs (129 N·m)
Important Notes
Tighten bolts in a criss-cross pattern to ensure even clamping force.
5 Trailing Arm to Frame Bolts
M14 x 2.0
5
Trailing Arm to Frame Bolts
M14 x 2.0
Torque Specification
90 ft-lbs (122 N·m)
Important Notes
Ensure trailing arm is properly aligned before tightening.
Steering
1 Tie Rod End to Steering Knuckle Nut
M12 x 1.5
1
Tie Rod End to Steering Knuckle Nut
M12 x 1.5
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Ensure the tie rod end stud is properly seated before tightening. Use a new nut if specified. Final torque should be achieved in one smooth pull.
2 Tie Rod to Steering Rack Bolt
M14 x 1.5
2
Tie Rod to Steering Rack Bolt
M14 x 1.5
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Tighten securely without overtightening. Use a new nut if specified. Final torque should be achieved in one smooth pull.
3 Steering Rack Mount Bolts
M10 x 1.5
3
Steering Rack Mount Bolts
M10 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Tighten all mounting bolts evenly and completely. Final torque should be achieved in one smooth pull.
4 Steering Shaft Lower Coupling Bolt
M8 x 1.25
4
Steering Shaft Lower Coupling Bolt
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure the steering shaft is properly aligned before tightening. Do not overtighten. Final torque should be achieved in one smooth pull.
Troubleshooting Guide
Common issues, diagnostic steps, and prevention guidelines
Common Issues
Bolt stretching, stripped threads, uneven torque patterns
Common Issues
Bolt stretching, stripped threads, uneven torque patterns
Loose Components
Symptoms:
- Rattling or vibration noises
- Visible movement in components
- Uneven panel gaps
Solutions:
- Clean threads and mounting surfaces
- Replace damaged fasteners
- Apply proper torque in sequence
- Use thread locker if specified
Stripped Fasteners
Symptoms:
- Unable to achieve proper torque
- Fastener spins freely
- Visible thread damage
Solutions:
- Use thread repair kit if appropriate
- Install thread insert (HeliCoil)
- Replace component if threaded hole is damaged
- Upgrade to higher grade fastener if recommended
Overtightened Components
Symptoms:
- Cracked or deformed parts
- Broken fasteners
- Compressed gaskets or seals
Solutions:
- Replace damaged components
- Use new fasteners
- Follow proper torque sequence
- Verify correct torque specifications
Diagnostic Steps
Visual inspection, torque verification, thread assessment
Diagnostic Steps
Visual inspection, torque verification, thread assessment
1
Visual Inspection
Inspect the affected area for any visible signs of damage or wear
- Check for cracks or deformation
- Look for signs of excessive wear
- Verify proper fastener installation
2
Torque Verification
Verify the torque applied to the fasteners
- Check the torque wrench calibration
- Verify the torque specification
- Compare the applied torque to the specification
3
Thread Assessment
Assess the condition of the threads
- Check for signs of thread damage
- Verify the thread type and size
- Check for proper thread engagement
Prevention Guidelines
Best practices, maintenance tips, tool care
Prevention Guidelines
Best practices, maintenance tips, tool care
Best Practices
- Always follow the recommended torque specification
- Use the correct type and size of fasteners
- Verify the torque wrench calibration regularly
Maintenance Tips
- Regularly inspect the affected area for signs of wear or damage
- Replace damaged or worn-out components promptly
- Keep the work area clean and organized
Tool Care
- Regularly clean and maintain the torque wrench
- Store the torque wrench in a dry and secure location
- Verify the torque wrench calibration before each use
Frequently Asked Questions
Find answers to common questions about torque specifications
Q1 What IS the recommended torque for cylinder head bolts on a 2008 Dodge Caliber?
Q1
What IS the recommended torque for cylinder head bolts on a 2008 Dodge Caliber?
89 ft-lbs (120 Nm) in three stages: 25 ft-lbs (34 Nm), 55 ft-lbs (75 Nm), and 89 ft-lbs (120 Nm).
Q2 What IS the correct torque for the front brake caliper mounting bolts on a 2012 Dodge Caliber?
Q2
What IS the correct torque for the front brake caliper mounting bolts on a 2012 Dodge Caliber?
110 ft-lbs (150 Nm) using a torque wrench.
Q3 What type of torque wrench IS recommended for tightening suspension components on a 2007 Dodge Caliber?
Q3
What type of torque wrench IS recommended for tightening suspension components on a 2007 Dodge Caliber?
A high-quality click-type or digital torque wrench with a range that covers the specified torque values.
Q4 IS it acceptable to use a torque multiplier to achieve higher torque values on my 2011 Dodge Caliber?
Q4
IS it acceptable to use a torque multiplier to achieve higher torque values on my 2011 Dodge Caliber?
No, torque multipliers are not recommended as they can damage bolts and compromise safety. Use a torque wrench with the appropriate range instead.
Environmental Considerations
Temperature, humidity, and seasonal effects on torque specifications
Temperature Effects
Includes: High Heat, Cold Weather, Thermal Cycling
Temperature Effects
Includes: High Heat, Cold Weather, Thermal Cycling
Temperature can significantly impact torque values and fastener behavior
Cold Weather
Effects:
- Increased material brittleness
- Higher torque required due to thread contraction
- Reduced thread lubricant effectiveness
Recommendations:
- Allow components to warm to room temperature when possible
- Consider using winter-grade thread lubricants
- Check torque values more frequently during winter months
Hot Weather
Effects:
- Thermal expansion of components
- Decreased friction in threads
- Accelerated lubricant breakdown
Recommendations:
- Check torque when components are at normal operating temperature
- Use temperature-resistant thread lockers
- Consider re-torquing after heat cycles
Humidity and Corrosion
Covers: Rust Prevention, Salt Exposure, Moisture Control
Humidity and Corrosion
Covers: Rust Prevention, Salt Exposure, Moisture Control
Moisture and corrosion can affect fastener integrity and torque values
High Humidity
Effects:
- Accelerated corrosion formation
- Reduced friction coefficient
- Potential thread seizing
Prevention:
- Use corrosion-resistant fasteners
- Apply appropriate anti-seize compounds
- Maintain proper protective coatings
Salt Exposure
Effects:
- Rapid corrosion development
- Thread damage
- Seized fasteners
Prevention:
- Regular underbody washing
- Use of sacrificial anodes where appropriate
- Application of protective coatings
Seasonal Maintenance
Spring, Summer, Fall, and Winter maintenance schedules
Seasonal Maintenance
Spring, Summer, Fall, and Winter maintenance schedules
Spring
- Inspect for winter damage
- Clean and protect exposed fasteners
- Check torque on critical components
Summer
- Monitor heat-affected components
- Check expansion-related loosening
- Inspect cooling system mounts
Fall
- Prepare for winter conditions
- Apply corrosion protection
- Verify all fasteners are properly torqued
Winter
- More frequent inspection of critical fasteners
- Check for salt damage
- Monitor suspension component torque
Related Resources
Tools, service procedures, and technical bulletins
Recommended Tools
Digital Torque Wrench (10-100 Nm)
Essential for tightening fasteners to precise torque specifications, preventing damage and ensuring proper assembly. This range IS suitable for many applications on the caliber.
- Digital display for accurate readings
- Audible alarm when target torque IS reached
- Multiple units (Nm, ft-lb, in-lb)
- Reversible ratcheting mechanism
Service Procedures
Bolt Torque Specifications for 2007-2012 Dodge Caliber
Comprehensive service procedure for applying correct torque to bolts and fasteners on the Dodge Caliber.
- Locate the specific bolt or fastener for which you need torque specifications.
- Reference the torque value in the supplied table or technical manual.
- Set your digital torque wrench to the specified torque value.
- Tighten the bolt or fastener using the torque wrench until the wrench clicks or beeps, indicating the desired torque has been achieved.
- Follow any additional instructions or safety precautions provided in the service manual.
Technical Service Bulletins
Legal Disclaimer
Important information about using this content
Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.
General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability
The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.
We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.
Technical Information
- All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
- Vehicle specifications and procedures may vary by model year, trim level, and region.
- Always follow the manufacturer's recommended procedures and safety precautions.
- Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
- If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.
About the Author
Expert automotive knowledge and experience
'/%3E%3Cpath d='M60 30a20 20 0 1 1 0 40 20 20 0 0 1 0-40zm0 45c16.5 0 30 7.5 30 16.8V100H30v-8.2c0-9.3 13.5-16.8 30-16.8z' fill='%23404040'/%3E%3C/svg%3E)
ASE
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions
Diagnostic
Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.
Repair
Expert in both traditional mechanical repairs and modern vehicle systems.
Additional Expertise
Documentation
Created over 500 detailed repair guides and technical documents.
Training
Conducted technical training sessions and contributed to repair databases.
Certifications & Research
Certifications
- ASE Master Technician Certification
- Advanced Diagnostic Specialist
- Hybrid/Electric Vehicle Systems
- Performance Tuning Expert
Research & Community
Actively researches emerging technologies and contributes to automotive forums.