Dodge Avenger 2008-2014
Dodge Avenger 2008-2014 Torque Specifications
Complete Dodge Avenger 2008-2014 torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.
Updated
Important Information
Safety guidelines and reference information for proper torque application
Safety First
- Always verify torque specifications with your vehicle's factory service manual
- Use properly calibrated torque wrenches
- Replace all torque-to-yield (TTY) bolts - they are single-use only
- When in doubt, consult a professional mechanic
Quick Reference Guide
Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083
Common Torque Patterns
Star Pattern
Used for wheels and other circular bolt patterns
Cross Pattern
Used for gaskets and cover plates
Sequential Pattern
Used for head bolts and other critical components
Common Mistakes to Avoid
Common Mistakes to Avoid
Over-tightening
Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.
Prevention:
Always use a calibrated torque wrench and follow specifications exactly.
Incorrect Torque Sequence
Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.
Prevention:
Follow the manufacturer's specified torque sequence pattern.
Dirty Threads
Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.
Prevention:
Clean and inspect all threads before assembly. Use new thread locker if specified.
Reusing TTY Bolts
Torque-to-yield bolts are designed to stretch and must not be reused.
Prevention:
Always replace TTY bolts with new ones. They are single-use only.
Dry vs. Lubricated
Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.
Prevention:
Check if specs are for dry or lubricated threads. Use specified lubricant when required.
Recommended Tools
Recommended Tools
Torque Wrench (1/4" Drive)
Range: 2-25 ft-lbs
Small fasteners, delicate components
Torque Wrench (3/8" Drive)
Range: 10-100 ft-lbs
Most common automotive fasteners
Torque Wrench (1/2" Drive)
Range: 30-250 ft-lbs
Large fasteners, wheels
Angle Gauge
Torque-to-yield (TTY) bolts
Torque Wrench Care
- Calibrate annually or after 5,000 clicks
- Store at lowest setting
- Keep clean and lubricated
Search Specifications
Search by component name, bolt size, or description
Type to search through torque specifications. Use arrow keys to navigate results. Press Enter to select a result.
Torque Calculator
Convert between different torque units
2.4l Engine
Torque specifications for 2.4L Engine
2.4l Engine
Torque specifications for 2.4L Engine
Cylinder Head
1 Cylinder Head Bolts
M12 x 1.75
1
Cylinder Head Bolts
M12 x 1.75
Torque Specification
1. 20 ft-lbs (27 N·m)
Important Notes
Tighten in specified sequence. Check manufacturer's diagram.
2 Valve Cover Bolts
M6 x 1.0
2
Valve Cover Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure even tightening to prevent leaks. Convert to inch pounds.
3 Rocker Arm/Shaft Bolts
M8 x 1.25
3
Rocker Arm/Shaft Bolts
M8 x 1.25
Torque Specification
21 ft-lbs (28 N·m)
Important Notes
Tighten evenly to prevent damage to the rocker arm assembly.
4 Camshaft Bearing Cap Bolts
M6 x 1.0
4
Camshaft Bearing Cap Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Follow torque sequence to ensure even bearing load. Estimated based on similar bolts.
Engine Block
1 Main Bearing Bolts
M12 x 1.75
1
Main Bearing Bolts
M12 x 1.75
Torque Specification
100 ft-lbs (135 N·m)
Important Notes
Tighten in the specified sequence.
2 Connecting Rod Nuts
M9 x 1.25
2
Connecting Rod Nuts
M9 x 1.25
Torque Specification
48 ft-lbs (65 N·m)
Important Notes
Ensure correct orientation of rod cap. Tighten evenly.
3 Oil Pan Bolts
M6 x 1.0
3
Oil Pan Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten evenly in a criss-cross pattern to avoid leaks.
4 Oil Filter Housing Bolts
M6 x 1.0
4
Oil Filter Housing Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure proper seal installation, convert to inch pounds.
5 Knock Sensor Bolt
M6 x 1.0
5
Knock Sensor Bolt
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Estimated based on similar bolts, convert to inch pounds.
6 Crankshaft Position Sensor Bolt
M6 x 1.0
6
Crankshaft Position Sensor Bolt
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Estimated based on similar bolts, convert to inch pounds.
7 Water Pump Bolts
M6 x 1.0
7
Water Pump Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten evenly to ensure proper seal, convert to inch pounds.
Rotating Assembly
1 Flywheel Bolts
M10 x 1.5
1
Flywheel Bolts
M10 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Tighten evenly in a star pattern.
2 Crankshaft Pulley/Harmonic Balancer Bolt
M14 x 1.5
2
Crankshaft Pulley/Harmonic Balancer Bolt
M14 x 1.5
Torque Specification
105 ft-lbs (142 N·m)
Important Notes
Ensure proper seating of the pulley. Always use a new bolt if specified.
3 Water Pump Pulley Bolts
M6 x 1.0
3
Water Pump Pulley Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten evenly, convert to inch pounds.
Timing System
1 Timing Belt/Chain Tensioner Bolt
M8 x 1.25
1
Timing Belt/Chain Tensioner Bolt
M8 x 1.25
Torque Specification
20.83 ft-lbs (28 N·m)
Important Notes
Ensure correct tensioner alignment, convert to inch pounds.
2 Camshaft Sprocket Bolt
M10 x 1.25
2
Camshaft Sprocket Bolt
M10 x 1.25
Torque Specification
75 ft-lbs (102 N·m)
Important Notes
Hold camshaft while tightening to prevent rotation.
3 Camshaft Position Sensor Bolt
M6 x 1.0
3
Camshaft Position Sensor Bolt
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Estimated based on similar bolts, convert to inch pounds.
Intake Exhaust
1 Throttle Body Bolts
M6 x 1.0
1
Throttle Body Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten in a criss-cross pattern to ensure a proper seal. Convert to inch pounds.
2 Intake Manifold Bolts
M6 x 1.0
2
Intake Manifold Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten evenly in a crisscross pattern. Convert to inch pounds.
3 Exhaust Manifold/Headers Bolts
M8 x 1.25
3
Exhaust Manifold/Headers Bolts
M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Tighten in a specified sequence. Check manufacturer's diagram.
4 EGR Valve Bolts
M6 x 1.0
4
EGR Valve Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure proper gasket or seal is in place. Convert to inch pounds.
Fuel System
1 Fuel Rail Bolts
M6 x 1.0
1
Fuel Rail Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten evenly, Convert to inch pounds.
2 Fuel Injector Bolts
M6 x 1.0
2
Fuel Injector Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten gently and evenly. Convert to inch pounds.
Ignition System
1 Spark Plugs
M14 x 1.25
1
Spark Plugs
M14 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure threads are clean before installation. Do not overtighten.
2 Ignition Coil Bolt
M6 x 1.0
2
Ignition Coil Bolt
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure proper seating of ignition coil, convert to inch pounds.
Cooling System
1 Thermostat Housing Bolts
M6 x 1.0
1
Thermostat Housing Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure proper gasket placement, convert to inch pounds.
2 Coolant Temperature Sensor Bolt/Port
M6 x 1.0
2
Coolant Temperature Sensor Bolt/Port
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure proper seal, this is an estimated value based on other sensors using similar bolts, convert to inch pounds
Ancillary Components
1 Serpentine/Accessory Drive Belt Tensioner Bolt
M8 x 1.25
1
Serpentine/Accessory Drive Belt Tensioner Bolt
M8 x 1.25
Torque Specification
20.83 ft-lbs (28 N·m)
Important Notes
Ensure proper tensioner alignment, convert to inch pounds.
2 Oil Drain Plug Bolt
M14 x 1.5
2
Oil Drain Plug Bolt
M14 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Use new crush washer if required. Do not overtighten.
2.7l Engine
Torque specifications for 2.7L Engine
2.7l Engine
Torque specifications for 2.7L Engine
Cylinder Head
1 Cylinder Head Bolts
M12 x 1.75
1
Cylinder Head Bolts
M12 x 1.75
Torque Specification
1. 20 ft-lbs (27 N·m)
2. 90°
Important Notes
Apply a torque sequence per service manual, typically from the center outward in a crisscross pattern. Always use new bolts per manufacturer recommendations.
2 Exhaust Manifold Studs to Cylinder Head
M8 x 1.25
2
Exhaust Manifold Studs to Cylinder Head
M8 x 1.25
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Install studs into the cylinder head before installing the exhaust manifold.
3 Exhaust Manifold to Cylinder Head Bolts
M8 x 1.25
3
Exhaust Manifold to Cylinder Head Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Torque bolts in a sequence working from the center out to the ends, repeat 2-3 times to ensure even clamping pressure
4 Cylinder Head Cover Bolts
M6 x 1.0
4
Cylinder Head Cover Bolts
M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Tighten bolts evenly in a crisscross pattern, starting from the center.
Crankshaft And Connecting Rod
1 Main Bearing Bolts
M10 x 1.5
1
Main Bearing Bolts
M10 x 1.5
Torque Specification
1. 15 ft-lbs (20 N·m)
2. 30 ft-lbs (41 N·m)
3. 90°
Important Notes
Apply a torque sequence working from the center outward in a crisscross pattern. Always use new bolts per manufacturer recommendations.
2 Connecting Rod Nuts
M9 x 1.25
2
Connecting Rod Nuts
M9 x 1.25
Torque Specification
48 ft-lbs (65 N·m)
Important Notes
Torque connecting rod nuts in two steps; a first torque step, then a final torque step, usually no torque angle is needed.
3 Flywheel Bolts
M10 x 1.5
3
Flywheel Bolts
M10 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Tighten bolts in a star pattern to ensure even clamping force.
4 Crankshaft Pulley/Harmonic Balancer Bolt
M14 x 1.5
4
Crankshaft Pulley/Harmonic Balancer Bolt
M14 x 1.5
Torque Specification
105 ft-lbs (142 N·m)
Important Notes
Ensure the crankshaft is locked to prevent rotation while tightening this bolt.
Valvetrain
1 Rocker Arms/Shafts Bolts
M8 x 1.25
1
Rocker Arms/Shafts Bolts
M8 x 1.25
Torque Specification
21 ft-lbs (28 N·m)
Important Notes
Tighten evenly in a crisscross pattern.
2 Camshaft Sprocket Bolt
M10 x 1.25
2
Camshaft Sprocket Bolt
M10 x 1.25
Torque Specification
75 ft-lbs (102 N·m)
Important Notes
Ensure camshaft is locked to prevent rotation while tightening this bolt.
Engine Covers And Sealing
1 Valve Cover Bolts
M6 x 1.0
1
Valve Cover Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Tighten bolts evenly in a crisscross pattern, starting from the center.
2 Oil Pan Bolts
M6 x 1.0
2
Oil Pan Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Tighten bolts evenly in a crisscross pattern to prevent gasket distortion.
3 Oil Drain Plug Bolt
M14 x 1.5
3
Oil Drain Plug Bolt
M14 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Use a new crush washer when installing the oil drain plug.
4 Oil Filter Housing Bolt
M6 x 1.0
4
Oil Filter Housing Bolt
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Tighten evenly and check for leaks after installation.
Intake And Exhaust
1 Intake Manifold Bolts
M6 x 1.0
1
Intake Manifold Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Tighten bolts in a sequence working from the center out to the ends.
2 Throttle Body Bolts
M6 x 1.0
2
Throttle Body Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Tighten bolts evenly, ensure a proper seal to prevent vacuum leaks.
3 EGR Valve Bolts
M6 x 1.0
3
EGR Valve Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure proper alignment to prevent exhaust leaks.
Fuel System
1 Fuel Rail Bolts
M6 x 1.0
1
Fuel Rail Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Tighten evenly to avoid fuel leaks.
2 Fuel Injector Bolts/Clips
M6 x 1.0
2
Fuel Injector Bolts/Clips
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Tighten evenly to ensure a proper seal. Some systems may use clips, check for secure fit.
Cooling System
1 Water Pump Bolts
M6 x 1.0
1
Water Pump Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Tighten bolts evenly to avoid leaks.
2 Water Pump Pulley Bolts
M6 x 1.0
2
Water Pump Pulley Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure proper alignment of pulley.
3 Thermostat Housing Bolts
M6 x 1.0
3
Thermostat Housing Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Tighten evenly, use new gasket or sealant.
4 Coolant Temperature Sensor Bolt/fitting
M10 x 1.0
4
Coolant Temperature Sensor Bolt/fitting
M10 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Do not overtighten the sensor, ensure proper seating to prevent leaks
Ignition System
1 Ignition Coil Bolts
M6 x 1.0
1
Ignition Coil Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Tighten evenly to ensure proper coil contact
2 Spark Plugs
M14 x 1.25
2
Spark Plugs
M14 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure plugs are seated correctly by hand first before torquing, using new spark plugs is recommended.
Sensors And Timing
1 Camshaft Position Sensor Bolt
M6 x 1.0
1
Camshaft Position Sensor Bolt
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Do not overtighten, ensure sensor is seated properly.
2 Crankshaft Position Sensor Bolt
M6 x 1.0
2
Crankshaft Position Sensor Bolt
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Do not overtighten, ensure sensor is seated properly.
3 Knock Sensor Bolt
M8 x 1.25
3
Knock Sensor Bolt
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure sensor is seated properly, and do not overtighten.
4 Timing Belt/Chain Tensioner Bolt
M8 x 1.25
4
Timing Belt/Chain Tensioner Bolt
M8 x 1.25
Torque Specification
21 ft-lbs (28 N·m)
Important Notes
Torque to specified value to maintain proper tension and engine timing. Always ensure proper timing procedures are followed.
3.5l Engine
Torque specifications for 3.5L Engine
3.5l Engine
Torque specifications for 3.5L Engine
Cylinder Head
1 Cylinder Head Bolts
M12 x 1.75
1
Cylinder Head Bolts
M12 x 1.75
Torque Specification
1. 20 ft-lbs (27 N·m)
2. 90°
3. 90°
Important Notes
Torque in sequence. Final torque achieved after two 90 degree angle turns. Consult service manual for specific sequence.
2 Rocker Arm Shaft Bolts
M8 x 1.25
2
Rocker Arm Shaft Bolts
M8 x 1.25
Torque Specification
21 ft-lbs (28 N·m)
Important Notes
Tighten evenly.
3 Spark Plugs
M14 x 1.25
3
Spark Plugs
M14 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure spark plugs are properly seated before torquing. Do not overtighten.
4 Exhaust Manifold/Headers to Cylinder Head Bolts
M10 x 1.5
4
Exhaust Manifold/Headers to Cylinder Head Bolts
M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Tighten in sequence from the center out. A multiple step torque is typically used on exhaust components. Final torque value should be 25 ft-lbs.
Engine Block
1 Main Bearing Bolts
M12 x 1.75
1
Main Bearing Bolts
M12 x 1.75
Torque Specification
1. 40 ft-lbs (54 N·m)
2. 70 ft-lbs (95 N·m)
3. 100 ft-lbs (135 N·m)
Important Notes
Torque in sequence. Multiple stages to reach final torque. Consult service manual for specific sequence.
2 Oil Pan Bolts
M6 x 1.0
2
Oil Pan Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten evenly in a criss-cross pattern.
3 Oil Filter Housing Bolts
M6 x 1.0
3
Oil Filter Housing Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten evenly in a criss-cross pattern.
4 Water Pump Bolts
M8 x 1.25
4
Water Pump Bolts
M8 x 1.25
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten evenly in a criss-cross pattern. Check the gasket.
5 Oil Drain Plug Bolt
M14 x 1.5
5
Oil Drain Plug Bolt
M14 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Use a new crush washer.
Internal Components
1 Connecting Rod Nuts
M9 x 1.25
1
Connecting Rod Nuts
M9 x 1.25
Torque Specification
1. 20 ft-lbs (27 N·m)
2. 48 ft-lbs (65 N·m)
Important Notes
Tighten in sequence. Consult service manual for specific sequence.
2 Camshaft Sprocket Bolt
M10 x 1.5
2
Camshaft Sprocket Bolt
M10 x 1.5
Torque Specification
75 ft-lbs (102 N·m)
Important Notes
Ensure correct camshaft alignment before tightening.
3 Crankshaft Pulley/Harmonic Balancer Bolt
M14 x 2.0
3
Crankshaft Pulley/Harmonic Balancer Bolt
M14 x 2.0
Torque Specification
105 ft-lbs (142 N·m)
Important Notes
Ensure the pulley is correctly seated.
4 Flywheel Bolts
M10 x 1.5
4
Flywheel Bolts
M10 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Tighten evenly in a criss-cross pattern.
Intake System
1 Intake Manifold Bolts
M6 x 1.0
1
Intake Manifold Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten evenly in a criss-cross pattern.
2 Throttle Body Bolts
M6 x 1.0
2
Throttle Body Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten evenly in a criss-cross pattern.
3 EGR Valve Bolts
M6 x 1.0
3
EGR Valve Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten evenly.
4 Mass Airflow Sensor Bolts
M5 x 0.8
4
Mass Airflow Sensor Bolts
M5 x 0.8
Torque Specification
4.4 ft-lbs (6 N·m)
Important Notes
Tighten evenly. Estimated value.
5 Intake Air Temperature Sensor Bolt/Fitting
M6 x 1.0
5
Intake Air Temperature Sensor Bolt/Fitting
M6 x 1.0
Torque Specification
5.9 ft-lbs (8 N·m)
Important Notes
Tighten carefully. Estimated value
6 PCV Valve Bolt
M6 x 1.0
6
PCV Valve Bolt
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
If PCV valve is bolted to the intake, this value applies. Estimated value.
Fuel System
1 Fuel Rail Bolts
M6 x 1.0
1
Fuel Rail Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten evenly.
2 Fuel Injector Bolts
M6 x 1.0
2
Fuel Injector Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten evenly.
Cooling System
1 Thermostat Housing Bolts
M6 x 1.0
1
Thermostat Housing Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten evenly. Check the gasket.
2 Water Pump Pulley Bolts
M6 x 1.0
2
Water Pump Pulley Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten evenly.
Electrical System
1 Crankshaft Position Sensor Bolt
M6 x 1.0
1
Crankshaft Position Sensor Bolt
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Tighten carefully. Estimated value.
2 Camshaft Position Sensor Bolt
M6 x 1.0
2
Camshaft Position Sensor Bolt
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Tighten carefully. Estimated value.
3 Knock Sensor Bolt
M8 x 1.25
3
Knock Sensor Bolt
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure sensor is correctly seated. Estimated value.
4 Ignition Coil Bolts
M6 x 1.0
4
Ignition Coil Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten evenly.
5 Engine Coolant Temperature Sensor Bolt/Fitting
M10 x 1.0
5
Engine Coolant Temperature Sensor Bolt/Fitting
M10 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Tighten carefully. Estimated value.
Valve Train
1 Valve Cover Bolts
M6 x 1.0
1
Valve Cover Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten evenly in a criss-cross pattern.
Timing System
1 Timing Belt/Chain Tensioner Bolt
M8 x 1.25
1
Timing Belt/Chain Tensioner Bolt
M8 x 1.25
Torque Specification
20.8 ft-lbs (28 N·m)
Important Notes
Verify tensioner is properly positioned.
Accessory Drive
1 Serpentine/Accessory Drive Belt Tensioner Bolt
M8 x 1.25
1
Serpentine/Accessory Drive Belt Tensioner Bolt
M8 x 1.25
Torque Specification
20.8 ft-lbs (28 N·m)
Important Notes
Verify tensioner is correctly seated. Estimated value.
2 Drive Belt Idler Pulley Bolt
M8 x 1.25
2
Drive Belt Idler Pulley Bolt
M8 x 1.25
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure idler pulley is correctly seated.
3.6l Engine
Torque specifications for 3.6L Engine
3.6l Engine
Torque specifications for 3.6L Engine
Cylinder Head and Valvetrain
1 Cylinder Head Bolts
M12 x 1.5
1
Cylinder Head Bolts
M12 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
2 Valve Cover Bolts
M8 x 1.25
2
Valve Cover Bolts
M8 x 1.25
Torque Specification
105 in-lbs (12 N·m)
3 Rocker Arms/Shafts Bolts
M10 x 1.5
3
Rocker Arms/Shafts Bolts
M10 x 1.5
Torque Specification
21 ft-lbs (28 N·m)
Engine Block and Crankshaft
1 Main Bearing Bolts
M14 x 2.0
1
Main Bearing Bolts
M14 x 2.0
Torque Specification
100 ft-lbs (135 N·m)
2 Crankshaft Pulley/Harmonic Balancer Bolt
M16 x 2.0
2
Crankshaft Pulley/Harmonic Balancer Bolt
M16 x 2.0
Torque Specification
105 ft-lbs (142 N·m)
Camshaft and Timing System
1 Camshaft Sprocket Bolt
M12 x 1.5
1
Camshaft Sprocket Bolt
M12 x 1.5
Torque Specification
75 ft-lbs (102 N·m)
2 Timing Belt/Chain Tensioner Bolt
M10 x 1.5
2
Timing Belt/Chain Tensioner Bolt
M10 x 1.5
Torque Specification
250 in-lbs (28 N·m)
Engine Mounts and Transmission
1 Engine Mounting Bolts
M12 x 1.5
1
Engine Mounting Bolts
M12 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Estimated value, not explicitly listed in the manual.
2 Engine Block to Transmission Bellhousing Bolts
M14 x 2.0
2
Engine Block to Transmission Bellhousing Bolts
M14 x 2.0
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Estimated value, not explicitly listed in the manual.
Intake and Exhaust System
1 Intake Manifold to Engine Block Bolts
M10 x 1.5
1
Intake Manifold to Engine Block Bolts
M10 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated value, not explicitly listed in the manual.
2 Exhaust Manifold to Engine Block Bolts
M10 x 1.5
2
Exhaust Manifold to Engine Block Bolts
M10 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated value, not explicitly listed in the manual.
Cooling System
1 Water Pump Bolts
M8 x 1.25
1
Water Pump Bolts
M8 x 1.25
Torque Specification
105 in-lbs (12 N·m)
2 Thermostat Housing Bolts
M8 x 1.25
2
Thermostat Housing Bolts
M8 x 1.25
Torque Specification
105 in-lbs (12 N·m)
Oil System
1 Oil Pan Bolts
M10 x 1.5
1
Oil Pan Bolts
M10 x 1.5
Torque Specification
105 in-lbs (12 N·m)
2 Oil Filter Cap
M12 x 1.5
2
Oil Filter Cap
M12 x 1.5
Torque Specification
Hand tight ft-lbs
3 Oil Drain Plug Bolt
M12 x 1.5
3
Oil Drain Plug Bolt
M12 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
41te Transmission
Torque specifications for 41te Transmission
41te Transmission
Torque specifications for 41te Transmission
Transmission Mounting
1 Transmission Mounting Bolts
M12 x 1.75
1
Transmission Mounting Bolts
M12 x 1.75
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure proper alignment before tightening. Use a cross-tightening pattern.
Transmission Case
1 Transmission Oil Pan Bolts
M6 x 1.0
1
Transmission Oil Pan Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten bolts in a cross pattern to prevent leaks. Inch-lbs converted to ft-lbs for consistency.
2 Transmission Range Sensor/PRNDL Switch Bolts
M6 x 1.0
2
Transmission Range Sensor/PRNDL Switch Bolts
M6 x 1.0
Torque Specification
6.67 ft-lbs (9 N·m)
Important Notes
Use caution not to overtighten and damage the sensor. Inch-lbs converted to ft-lbs for consistency.
3 Solenoid Pack Mounting Bolts
M6 x 1.0
3
Solenoid Pack Mounting Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten bolts in a cross pattern to ensure even pressure. Inch-lbs converted to ft-lbs for consistency.
4 Valve Body Mounting Bolts
M6 x 1.0
4
Valve Body Mounting Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Tighten bolts in a cross pattern to ensure even pressure. Inch-lbs converted to ft-lbs for consistency.
5 Input Speed Sensor Mounting Bolt
M6 x 1.0
5
Input Speed Sensor Mounting Bolt
M6 x 1.0
Torque Specification
6.67 ft-lbs (9 N·m)
Important Notes
Use caution not to overtighten and damage the sensor. Inch-lbs converted to ft-lbs for consistency.
6 Output Speed Sensor Mounting Bolt
M6 x 1.0
6
Output Speed Sensor Mounting Bolt
M6 x 1.0
Torque Specification
6.67 ft-lbs (9 N·m)
Important Notes
Use caution not to overtighten and damage the sensor. Inch-lbs converted to ft-lbs for consistency.
Fluid Ports
1 Transmission Drain and Fill Plugs
M18 x 1.5
1
Transmission Drain and Fill Plugs
M18 x 1.5
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Use a new sealing washer each time. Do not overtighten.
2 Transmission Cooler Line Fittings (at the transmission)
M16 x 1.5 (Banjo Bolt)
2
Transmission Cooler Line Fittings (at the transmission)
M16 x 1.5 (Banjo Bolt)
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Use new sealing washers. Ensure proper line alignment before tightening.
Drivetrain
1 Drive Axle/Half Shaft Bolts
M10 x 1.5
1
Drive Axle/Half Shaft Bolts
M10 x 1.5
Torque Specification
120 ft-lbs (163 N·m)
Important Notes
Ensure the axle is properly seated and aligned. Use proper thread locking compound.
2 Torque Converter Housing Bolts
M12 x 1.75
2
Torque Converter Housing Bolts
M12 x 1.75
Torque Specification
1. 40 ft-lbs (54 N·m)
2. 45 ft-lbs (61 N·m)
Important Notes
Tighten the bolts evenly using cross-tightening pattern. Torque value can vary. Check your vehicle's specific manual for this value. This is an estimated range, check manual first.
62te Transmission
Torque specifications for 62te Transmission
62te Transmission
Torque specifications for 62te Transmission
Transmission Mounting
1 Transmission Mounting Bolts
M12 x 1.75
1
Transmission Mounting Bolts
M12 x 1.75
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure proper alignment during installation. Tighten evenly to prevent stress.
Transmission Case
1 Transmission Case Bolts/Through Bolts
M10 x 1.5
1
Transmission Case Bolts/Through Bolts
M10 x 1.5
Torque Specification
1. 25 ft-lbs (34 N·m)
2. 90°
Important Notes
Follow the specified torque sequence and angle for proper case sealing and alignment. Manufacturer specified angle may vary, refer to the specific vehicle service manual.
2 Input Speed Sensor Bolt
M6 x 1.0
2
Input Speed Sensor Bolt
M6 x 1.0
Torque Specification
5.8 ft-lbs (7.9 N·m)
Important Notes
Do not overtighten. Ensure sensor is flush with the mounting surface.
3 Output Speed Sensor Bolt
M6 x 1.0
3
Output Speed Sensor Bolt
M6 x 1.0
Torque Specification
5.8 ft-lbs (7.9 N·m)
Important Notes
Do not overtighten. Ensure sensor is flush with the mounting surface.
4 Transmission Range Sensor/TFP Sensor Bolts
M5 x 0.8
4
Transmission Range Sensor/TFP Sensor Bolts
M5 x 0.8
Torque Specification
5.8 ft-lbs (7.9 N·m)
Important Notes
Do not overtighten. Sensor housing is plastic, be careful to apply even torque.
Valve Body And Solenoid
1 Valve Body Bolts
M6 x 1.0
1
Valve Body Bolts
M6 x 1.0
Torque Specification
8.3 ft-lbs (11.3 N·m)
Important Notes
Torque evenly to prevent distortion of the valve body. These bolts may be of different lengths, pay attention to location during disassembly.
2 Transmission Solenoid Pack Bolts
M6 x 1.0
2
Transmission Solenoid Pack Bolts
M6 x 1.0
Torque Specification
8.3 ft-lbs (11.3 N·m)
Important Notes
Do not over tighten. Ensure proper alignment to prevent leaks.
Oil Pan
1 Transmission Oil Pan Bolts
M6 x 1.0
1
Transmission Oil Pan Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Torque evenly to ensure proper gasket seal and prevent leaks. Use a new gasket or sealant.
Fluid Plugs
1 Transmission Drain and Fill Plugs
Tapered Pipe or M18 x 1.5
1
Transmission Drain and Fill Plugs
Tapered Pipe or M18 x 1.5
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Use a new crush washer or sealant as needed. Do not overtighten.
Bell Housing
1 Bell Housing Bolts
M12 x 1.75
1
Bell Housing Bolts
M12 x 1.75
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure proper alignment. Torque evenly to avoid stress. Check for proper mating of the engine and transmission.
Oil Cooler Lines
1 Transmission Oil Cooler Line Fittings
Varies (Banjo Bolt M12 x 1.5 or Flare Nut 1/2-20)
1
Transmission Oil Cooler Line Fittings
Varies (Banjo Bolt M12 x 1.5 or Flare Nut 1/2-20)
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Use new sealing washers. Do not overtighten. Ensure proper alignment of fittings.
Torque Converter
1 Torque Converter Bolts
M10 x 1.5
1
Torque Converter Bolts
M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure proper alignment. Torque bolts evenly to avoid imbalance or damage.
Body
Torque specifications for Body
Body
Torque specifications for Body
Fuel System
1 Fuel Tank Strap Bolts
M10 x 1.5
1
Fuel Tank Strap Bolts
M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure fuel tank is properly supported before tightening. Tighten to specified torque in a single step.
2 Fuel Filler Neck Bolts
M8 x 1.25
2
Fuel Filler Neck Bolts
M8 x 1.25
Torque Specification
50 ft-lbs (68 N·m)
Important Notes
Ensure proper alignment of the filler neck to the body. Tighten evenly to specified torque.
Door System
1 Door Hinge Bolts (Body Side)
M8 x 1.25
1
Door Hinge Bolts (Body Side)
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Tighten evenly to ensure proper door alignment. Check door operation after tightening.
2 Door Latch Striker Bolts
M8 x 1.25
2
Door Latch Striker Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Adjust striker for proper door latch engagement. Check door closure after tightening.
Exterior Panels
1 Fender Mounting Bolts
M6 x 1.0
1
Fender Mounting Bolts
M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Install bolts evenly to ensure flush mounting and prevent panel stress. May require panel adjustment.
2 Bumper Cover Mounting Bolts
M6 x 1.0
2
Bumper Cover Mounting Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Do not overtighten, as this can damage the bumper cover or mounting tabs.
3 Body Panel Mounting Bolts
M6 x 1.0
3
Body Panel Mounting Bolts
M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Apply torque evenly to prevent distortion of the panels. Commonly used on smaller panels.
Hood System
1 Hood Hinge Bolts (Body Side)
M8 x 1.25
1
Hood Hinge Bolts (Body Side)
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure proper alignment of the hood. Check hood operation after tightening.
2 Hood Latch Mounting Bolts
M6 x 1.0
2
Hood Latch Mounting Bolts
M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Adjust latch for proper hood engagement. Check latch operation after tightening.
Lighting
1 Headlight Mounting Bolts
M6 x 1.0
1
Headlight Mounting Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten carefully to prevent damage to mounting tabs. Check headlight alignment after tightening.
2 Taillight Mounting Bolts
M6 x 1.0
2
Taillight Mounting Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten evenly to avoid damaging the taillight housing or compromising the seal.
Grille System
1 Grille Mounting Bolts
M6 x 1.0
1
Grille Mounting Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure grille is properly aligned before tightening. Avoid overtightening.
Interior Components
1 Seat Mounting Bolts
M10 x 1.5
1
Seat Mounting Bolts
M10 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
This is a critical safety item. Ensure bolts are fully engaged and properly torqued.
2 Dashboard Mounting Bolts
M6 x 1.0
2
Dashboard Mounting Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten evenly. Ensure all trim clips are fully engaged before applying full torque. Do not overtighten.
Brakes
Torque specifications for Brakes
Brakes
Torque specifications for Brakes
Front Brake Caliper
1 Caliper Guide Pin Bolts
M10 x 1.25
1
Caliper Guide Pin Bolts
M10 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
These bolts secure the caliper body to the caliper mounting bracket. Tighten to specified torque, ensuring the caliper slides freely on the pins.
2 Caliper Mounting Bracket Bolts
M12 x 1.75
2
Caliper Mounting Bracket Bolts
M12 x 1.75
Torque Specification
80 ft-lbs (108 N·m)
Important Notes
These bolts secure the caliper mounting bracket to the steering knuckle. Ensure bolts are properly torqued for brake system stability.
3 Brake Hose Banjo Bolt
M10 x 1.0
3
Brake Hose Banjo Bolt
M10 x 1.0
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Secures the brake hose to the caliper. Use new sealing washers. Do not overtighten.
4 Caliper Bleeder Screw
M7 x 1.0
4
Caliper Bleeder Screw
M7 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
The bleeder screw is critical for brake bleeding; do not over or under-tighten.
Rear Brake Caliper
1 Caliper Guide Pin Bolts
M10 x 1.25
1
Caliper Guide Pin Bolts
M10 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
These bolts secure the caliper body to the caliper mounting bracket. Tighten to specified torque, ensuring the caliper slides freely on the pins.
2 Caliper Mounting Bracket Bolts
M12 x 1.75
2
Caliper Mounting Bracket Bolts
M12 x 1.75
Torque Specification
80 ft-lbs (108 N·m)
Important Notes
These bolts secure the caliper mounting bracket to the steering knuckle. Ensure bolts are properly torqued for brake system stability.
3 Brake Hose Banjo Bolt
M10 x 1.0
3
Brake Hose Banjo Bolt
M10 x 1.0
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Secures the brake hose to the caliper. Use new sealing washers. Do not overtighten.
4 Caliper Bleeder Screw
M7 x 1.0
4
Caliper Bleeder Screw
M7 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
The bleeder screw is critical for brake bleeding; do not over or under-tighten.
Brake Disc Drum
1 Brake Disc Retaining Bolts
M12 x 1.5
1
Brake Disc Retaining Bolts
M12 x 1.5
Torque Specification
105 ft-lbs (142 N·m)
Important Notes
These bolts secure the rotor to the hub assembly. Tighten in a star pattern. Ensure proper seating and no warpage.
Master Cylinder
1 Master Cylinder to Brake Booster Mounting Nuts
M8 x 1.25
1
Master Cylinder to Brake Booster Mounting Nuts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
These nuts secure the master cylinder to the booster. Tighten evenly to ensure a secure and flush connection. Estimated value based on bolt size.
Brake Booster
1 Brake Booster to Firewall Mounting Nuts
M8 x 1.25
1
Brake Booster to Firewall Mounting Nuts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
These nuts secure the booster to the firewall. Tighten evenly. Estimated value based on bolt size.
Drivetrain
Torque specifications for Drivetrain
Drivetrain
Torque specifications for Drivetrain
Engine To Transmission
1 Flywheel Bolts
M10 x 1.25
1
Flywheel Bolts
M10 x 1.25
Torque Specification
1. 40 ft-lbs (54 N·m)
2. 85 ft-lbs (115 N·m)
Important Notes
Tighten bolts in a star pattern to ensure even clamping. Torque in two stages, first to 40 ft-lbs, then to final torque of 85 ft-lbs.
2 Starter Motor Mounting Bolts
M10 x 1.5
2
Starter Motor Mounting Bolts
M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure proper starter alignment before tightening.
3 Transmission Mounting Bolts
M12 x 1.75
3
Transmission Mounting Bolts
M12 x 1.75
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Tighten evenly to ensure proper alignment.
Transmission Components
1 Transmission Oil Pan Bolts
M6 x 1.0
1
Transmission Oil Pan Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Torque bolts evenly in a cross pattern. Do not over-tighten to avoid warping the pan.
2 Transmission Drain and Fill Plugs
M18 x 1.5
2
Transmission Drain and Fill Plugs
M18 x 1.5
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Use a new crush washer or sealant when reinstalling. Do not over tighten.
3 Transmission Output Shaft Flange Nut
M24 x 1.5
3
Transmission Output Shaft Flange Nut
M24 x 1.5
Torque Specification
125 ft-lbs (170 N·m)
Important Notes
Estimated value based on similar components. Always use a new nut.
4 Transmission Cooler Line Fittings
M16 x 1.5
4
Transmission Cooler Line Fittings
M16 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Estimated value based on similar components and sizes, do not over tighten to prevent leaks.
Driveshaft And Axles
1 Drive Axle/Half Shaft Bolts
M10 x 1.5
1
Drive Axle/Half Shaft Bolts
M10 x 1.5
Torque Specification
120 ft-lbs (163 N·m)
Important Notes
Ensure proper alignment of the CV joint flange before tightening.
2 CV Joint/Axle Nut
M24 x 1.5
2
CV Joint/Axle Nut
M24 x 1.5
Torque Specification
185 ft-lbs (251 N·m)
Important Notes
Use a new nut. This nut is critical for bearing preload.
3 Propeller/Drive Shaft Bolts
M10 x 1.25
3
Propeller/Drive Shaft Bolts
M10 x 1.25
Torque Specification
50 ft-lbs (68 N·m)
Important Notes
Ensure the driveshaft is properly aligned before tightening.
Differential And Transfer Case
1 Differential Drain/Fill Plug
M18 x 1.5
1
Differential Drain/Fill Plug
M18 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Use a new crush washer or sealant when reinstalling.
2 Transfer Case Drain/Fill Plug
M18 x 1.5
2
Transfer Case Drain/Fill Plug
M18 x 1.5
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Use a new crush washer or sealant when reinstalling.
3 Differential Housing Mounting Bolts
M12 x 1.75
3
Differential Housing Mounting Bolts
M12 x 1.75
Torque Specification
75 ft-lbs (102 N·m)
Important Notes
Estimated value based on similar components and sizes, tighten evenly in a cross pattern.
4 Differential Cover Bolts
M8 x 1.25
4
Differential Cover Bolts
M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Tighten evenly in a cross pattern to prevent leaks, do not overtighten.
Electrical
Torque specifications for Electrical
Electrical
Torque specifications for Electrical
Ignition System
1 Ignition Coil Mounting Bolt
M6 x 1.0
1
Ignition Coil Mounting Bolt
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
Ensure coil is properly seated before tightening. Overtightening can damage the coil or mounting points.
Starting System
1 Starter Motor Mounting Bolts
M10 x 1.5
1
Starter Motor Mounting Bolts
M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure starter motor is properly aligned before tightening. Use new bolts if specified in vehicle service manual.
Charging System
1 Alternator Mounting Bolts
M10 x 1.5
1
Alternator Mounting Bolts
M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the alternator is correctly aligned with its bracket. Do not overtighten.
Battery And Cables
1 Battery Terminal Nuts
M6 x 1.0
1
Battery Terminal Nuts
M6 x 1.0
Torque Specification
7.9 ft-lbs (11 N·m)
Important Notes
Do not overtighten to avoid damaging terminals. Ensure terminals are clean and free of corrosion.
2 Ground Strap/Cable Mounting Bolt (Body/Frame, M6/M8)
M6 x 1.0 or M8 x 1.25
2
Ground Strap/Cable Mounting Bolt (Body/Frame, M6/M8)
M6 x 1.0 or M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure mounting surface is clean and free of corrosion. Torque value applies to M6/M8 bolt. Ensure correct bolt size before tightening.
3 Ground Strap/Cable Mounting Bolt (Body/Frame, M10)
M10 x 1.5
3
Ground Strap/Cable Mounting Bolt (Body/Frame, M10)
M10 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure mounting surface is clean and free of corrosion. Use a lock washer for secure mounting.
Control Modules
1 Engine Control Module (ECM) / Powertrain Control Module (PCM) Mounting Bolts
M6 x 1.0
1
Engine Control Module (ECM) / Powertrain Control Module (PCM) Mounting Bolts
M6 x 1.0
Torque Specification
6.7 ft-lbs (9 N·m)
Important Notes
Do not overtighten to avoid damaging the control module housing or mounting tabs. Ensure module is properly seated.
2 Body Control Module (BCM) Mounting Bolts
M6 x 1.0
2
Body Control Module (BCM) Mounting Bolts
M6 x 1.0
Torque Specification
6.7 ft-lbs (9 N·m)
Important Notes
Do not overtighten to avoid damaging the control module housing. Ensure BCM is properly seated.
Power Distribution
1 Fuse Box/Power Distribution Box Mounting Bolts
M6 x 1.0
1
Fuse Box/Power Distribution Box Mounting Bolts
M6 x 1.0
Torque Specification
6.7 ft-lbs (9 N·m)
Important Notes
Ensure the box is properly aligned before tightening. Do not overtighten.
Sensors
1 Crankshaft Position Sensor Mounting Bolt
M6 x 1.0
1
Crankshaft Position Sensor Mounting Bolt
M6 x 1.0
Torque Specification
6.7 ft-lbs (9 N·m)
Important Notes
Ensure the sensor is properly seated and aligned with the target wheel. Do not overtighten.
2 Camshaft Position Sensor Mounting Bolt
M6 x 1.0
2
Camshaft Position Sensor Mounting Bolt
M6 x 1.0
Torque Specification
6.7 ft-lbs (9 N·m)
Important Notes
Ensure the sensor is properly seated. Do not overtighten.
3 Knock Sensor Mounting Bolt
M6 x 1.0
3
Knock Sensor Mounting Bolt
M6 x 1.0
Torque Specification
6.7 ft-lbs (9 N·m)
Important Notes
Ensure the sensor is properly seated. Do not overtighten. Use care not to damage the sensor when tightening.
Emissions Sensors
Torque specifications for Emissions_sensors
Emissions Sensors
Torque specifications for Emissions_sensors
Egr System
1 EGR Valve Mounting Bolts
M8 x 1.25
1
EGR Valve Mounting Bolts
M8 x 1.25
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure proper gasket alignment to prevent leaks. Use a calibrated torque wrench. Torque bolts evenly to spec
Exhaust System
1 Exhaust Manifold to Cylinder Head Bolts
M10 x 1.5
1
Exhaust Manifold to Cylinder Head Bolts
M10 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Tighten in a cross pattern to prevent warping. Use new gaskets when reassembling. Use a calibrated torque wrench.
2 Exhaust Manifold/Header Flange Bolts
M10 x 1.5
2
Exhaust Manifold/Header Flange Bolts
M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Use new gaskets when reassembling. Ensure even clamping pressure. Use a calibrated torque wrench.
3 Catalytic Converter to Exhaust Pipe Bolts
M10 x 1.5
3
Catalytic Converter to Exhaust Pipe Bolts
M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Use new gaskets when reassembling. Ensure even clamping pressure. Use a calibrated torque wrench.
Intake System
1 Mass Airflow (MAF) Sensor Mounting Bolts
M5 x 0.8
1
Mass Airflow (MAF) Sensor Mounting Bolts
M5 x 0.8
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Do not over-tighten. Ensure the sensor is properly seated. Use a calibrated torque wrench. These values are estimated; consult a vehicle specific manual for exact spec.
2 Manifold Absolute Pressure (MAP) Sensor Mounting Bolts
M5 x 0.8
2
Manifold Absolute Pressure (MAP) Sensor Mounting Bolts
M5 x 0.8
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Do not over-tighten. Ensure the sensor is properly seated. Use a calibrated torque wrench. These values are estimated; consult a vehicle specific manual for exact spec.
Fuel System
1 Fuel Tank Pressure Sensor Mounting Screws
M4 x 0.7
1
Fuel Tank Pressure Sensor Mounting Screws
M4 x 0.7
Torque Specification
3 ft-lbs (4 N·m)
Important Notes
Do not over-tighten. Ensure the sensor is properly seated. Use a calibrated torque wrench. These values are estimated; consult a vehicle specific manual for exact spec.
Oxygen Sensors
1 Oxygen Sensor Threaded into Exhaust Pipe
M18 x 1.5
1
Oxygen Sensor Threaded into Exhaust Pipe
M18 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Apply anti-seize compound to threads if not pre-coated. Use a torque wrench, be careful not to cross thread. These values are estimated; consult a vehicle specific manual for exact spec.
2 Oxygen Sensor Mounting Flange Bolts
M8 x 1.25
2
Oxygen Sensor Mounting Flange Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Use new gasket if equipped. Tighten in a cross pattern. These values are estimated; consult a vehicle specific manual for exact spec.
Exhaust
Torque specifications for Exhaust
Exhaust
Torque specifications for Exhaust
Exhaust Manifold
1 Exhaust Manifold to Cylinder Head Bolts
M8 x 1.25
1
Exhaust Manifold to Cylinder Head Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Apply anti-seize to bolt threads. Torque in a cross pattern in multiple stages. Replace gasket upon reassembly.
2 Exhaust Manifold/Header Bolts
M10 x 1.5
2
Exhaust Manifold/Header Bolts
M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Apply anti-seize to bolt threads. Torque in a cross pattern in multiple stages. Replace gasket upon reassembly. May use a crush ring on some applications.
Exhaust Piping
1 Exhaust Pipe to Exhaust Manifold/Header Bolts
M10 x 1.5
1
Exhaust Pipe to Exhaust Manifold/Header Bolts
M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Apply anti-seize to bolt threads. Torque in a cross pattern in multiple stages. Always replace gaskets or crush rings.
2 Catalytic Converter to Exhaust Pipe Bolts
M10 x 1.5
2
Catalytic Converter to Exhaust Pipe Bolts
M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Apply anti-seize to bolt threads. Torque in a cross pattern in multiple stages. Ensure proper orientation of catalytic converter.
3 Muffler to Exhaust Pipe Bolts
M10 x 1.5
3
Muffler to Exhaust Pipe Bolts
M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Apply anti-seize to bolt threads. Torque in a cross pattern in multiple stages. Ensure the muffler is properly aligned.
4 Exhaust Flange Studs to Exhaust Flange Nuts
M10 x 1.5
4
Exhaust Flange Studs to Exhaust Flange Nuts
M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Apply anti-seize to stud threads and nut. Torque in a cross pattern. Replace nuts if damaged or corroded.
Exhaust Support
1 Exhaust Hanger Bolts/Nuts
M8 x 1.25
1
Exhaust Hanger Bolts/Nuts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Apply anti-seize to bolt threads. Ensure hangers are properly aligned and tightened evenly.
2 Exhaust Flex Pipe Clamp Bolts
M8 x 1.25
2
Exhaust Flex Pipe Clamp Bolts
M8 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Apply anti-seize to bolt threads. Tighten the clamp evenly to ensure a leak-free seal. Estimated value.
Sensors
1 Oxygen Sensor
M18 x 1.5
1
Oxygen Sensor
M18 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Do NOT use anti-seize on the sensor threads. Over-tightening can damage the sensor. Use sensor socket.
Fuel
Torque specifications for Fuel
Fuel
Torque specifications for Fuel
Fuel Rail
1 Fuel Rail Mounting Bolts
M8 x 1.25
1
Fuel Rail Mounting Bolts
M8 x 1.25
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure bolts are tightened evenly to prevent leaks. It is recommended to do a final pass with the torque wrench.
2 Fuel Injector Mounting Bolts/Screws
M6 x 1.0
2
Fuel Injector Mounting Bolts/Screws
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
These bolts secure the injectors to the fuel rail or intake manifold, ensure proper seating, preventing leaks, and maintaining injector efficiency.
3 Fuel Line Flare Nut (to fuel rail)
Varies, see notes
3
Fuel Line Flare Nut (to fuel rail)
Varies, see notes
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Torque value is an estimate and may vary based on fitting size. Always use a flare nut wrench to prevent rounding the nut. Consult service manual for specific torque.
Fuel Pump
1 Fuel Pump Mounting Bolts
M6 x 1.0
1
Fuel Pump Mounting Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure bolts are tightened evenly to ensure a secure seal. This value is an estimate and the specific service manual should be consulted.
2 Fuel Tank Sending Unit/Lock Ring
Lock ring, size specific
2
Fuel Tank Sending Unit/Lock Ring
Lock ring, size specific
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Torque value is estimated and specific to the lock ring. Use a lock ring tool when possible. Check the service manual for exact specification.
Fuel Filter
1 Fuel Filter Bolt/Nut
M10 x 1.5
1
Fuel Filter Bolt/Nut
M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
This ensures a proper seal within the fuel filter housing. Do not overtighten.
Hvac
Torque specifications for Hvac
Hvac
Torque specifications for Hvac
Ac Compressor
1 A/C Compressor Mounting Bolts
M10 x 1.5
1
A/C Compressor Mounting Bolts
M10 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure compressor is properly aligned before tightening. Do not overtighten, as this can damage the compressor housing.
Ac Lines
1 A/C Line Fittings
Varies (typically M16 x 1.5 - M22 x 1.5)
1
A/C Line Fittings
Varies (typically M16 x 1.5 - M22 x 1.5)
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
Use new O-rings or seals at each fitting. Some fittings may require lower torque; consult specific service data if available. Be cautious not to overtighten and cause damage.
Ac Condenser
1 A/C Condenser Mounting Bolts
M6 x 1.0
1
A/C Condenser Mounting Bolts
M6 x 1.0
Torque Specification
8.75 ft-lbs (12 N·m)
Important Notes
This is an estimated value. Verify with component-specific service data. Do not overtighten, as this can damage the condenser mounting points. Use a calibrated in-lbs torque wrench for accuracy.
Ac Evaporator
1 A/C Evaporator Core Housing Bolts
M5 x 0.8
1
A/C Evaporator Core Housing Bolts
M5 x 0.8
Torque Specification
5.8 ft-lbs (8 N·m)
Important Notes
This is an estimated value. Verify with component-specific service data. Be careful not to overtighten, as this can damage the plastic housing. Use a calibrated in-lbs torque wrench for accuracy.
Blower Motor
1 HVAC Blower Motor Mounting Bolts
M5 x 0.8
1
HVAC Blower Motor Mounting Bolts
M5 x 0.8
Torque Specification
5.8 ft-lbs (8 N·m)
Important Notes
This is an estimated value. Verify with component-specific service data. Do not overtighten, as this can cause cracking of the plastic housing. Use a calibrated in-lbs torque wrench for accuracy.
Mode Door Actuator
1 Mode Door Actuator Mounting Bolts
M5 x 0.8
1
Mode Door Actuator Mounting Bolts
M5 x 0.8
Torque Specification
5.8 ft-lbs (8 N·m)
Important Notes
This is an estimated value. Verify with component-specific service data. Avoid overtightening to prevent damage to the plastic housing. Use a calibrated in-lbs torque wrench for accuracy.
Blend Door Actuator
1 Blend Door Actuator Mounting Bolts
M5 x 0.8
1
Blend Door Actuator Mounting Bolts
M5 x 0.8
Torque Specification
5.8 ft-lbs (8 N·m)
Important Notes
This is an estimated value. Verify with component-specific service data. Do not overtighten to prevent cracking the plastic housing. Use a calibrated in-lbs torque wrench for accuracy.
Control Panel
1 HVAC Control Panel Mounting Bolts
M5 x 0.8
1
HVAC Control Panel Mounting Bolts
M5 x 0.8
Torque Specification
5.8 ft-lbs (8 N·m)
Important Notes
This is an estimated value. Verify with component-specific service data. Overtightening may cause damage to the dashboard. Use a calibrated in-lbs torque wrench for accuracy.
Suspension
Torque specifications for Suspension
Suspension
Torque specifications for Suspension
Front Struts
1 Strut to Steering Knuckle Bolts
M14 x 1.5
1
Strut to Steering Knuckle Bolts
M14 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Ensure bolts are properly engaged before torquing. Use a new bolt if the manual specifies.
2 Strut Top Mount Nuts/Bolts
M10 x 1.25
2
Strut Top Mount Nuts/Bolts
M10 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Torque values can vary based on the top mount design. Use caution not to overtighten. Value is an educated estimate.
Front Control Arms
1 Control Arm to Frame/Subframe Bolts
M14 x 2.0
1
Control Arm to Frame/Subframe Bolts
M14 x 2.0
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Ensure the control arm is properly aligned before tightening.
2 Lower Control Arm Ball Joint to Steering Knuckle Bolt
M12 x 1.75
2
Lower Control Arm Ball Joint to Steering Knuckle Bolt
M12 x 1.75
Torque Specification
80 ft-lbs (108 N·m)
Important Notes
Ensure the ball joint is seated properly before tightening. This torque is an educated estimate.
Steering
1 Tie Rod End Nut
M12 x 1.25
1
Tie Rod End Nut
M12 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Tighten to specified torque, ensure proper alignment.
2 Steering Gear/Rack Mounting Bolts
M12 x 1.75
2
Steering Gear/Rack Mounting Bolts
M12 x 1.75
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Ensure the steering gear is correctly aligned before torquing these bolts.
Sway Bar
1 Sway Bar Link Nuts
M10 x 1.5
1
Sway Bar Link Nuts
M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure links are correctly positioned.
2 Sway Bar Bushing Bracket Bolts
M8 x 1.25
2
Sway Bar Bushing Bracket Bolts
M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Do not overtighten these bolts, ensure the bushing bracket is properly aligned. Value is an educated estimate.
Rear Suspension
1 Rear Trailing Arm Bolts
M14 x 2.0
1
Rear Trailing Arm Bolts
M14 x 2.0
Torque Specification
100 ft-lbs (135 N·m)
Important Notes
Ensure proper alignment of the trailing arm before tightening. This torque is an educated estimate.
2 Rear Shock Absorber Mounting Bolts/Nuts
M12 x 1.75
2
Rear Shock Absorber Mounting Bolts/Nuts
M12 x 1.75
Torque Specification
70 ft-lbs (95 N·m)
Important Notes
Ensure the shock absorber is properly seated before torquing. This is an estimated torque.
Wheel Hub
1 Wheel Hub/Bearing Mounting Bolts
M12 x 1.5
1
Wheel Hub/Bearing Mounting Bolts
M12 x 1.5
Torque Specification
80 ft-lbs (108 N·m)
Important Notes
Ensure the hub is correctly seated before torquing the bolts. This torque is an estimate.
Ball Joints
1 Ball Joint Nut
M14 x 1.5
1
Ball Joint Nut
M14 x 1.5
Torque Specification
105 ft-lbs (142 N·m)
Important Notes
Ensure the ball joint stud is properly seated before tightening.
Troubleshooting Guide
Common issues, diagnostic steps, and prevention guidelines
Common Issues
Bolt stretching, stripped threads, uneven torque patterns
Common Issues
Bolt stretching, stripped threads, uneven torque patterns
Loose Components
Symptoms:
- Rattling or vibration noises
- Visible movement in components
- Uneven panel gaps
Solutions:
- Clean threads and mounting surfaces
- Replace damaged fasteners
- Apply proper torque in sequence
- Use thread locker if specified
Stripped Fasteners
Symptoms:
- Unable to achieve proper torque
- Fastener spins freely
- Visible thread damage
Solutions:
- Use thread repair kit if appropriate
- Install thread insert (HeliCoil)
- Replace component if threaded hole is damaged
- Upgrade to higher grade fastener if recommended
Overtightened Components
Symptoms:
- Cracked or deformed parts
- Broken fasteners
- Compressed gaskets or seals
Solutions:
- Replace damaged components
- Use new fasteners
- Follow proper torque sequence
- Verify correct torque specifications
Diagnostic Steps
Visual inspection, torque verification, thread assessment
Diagnostic Steps
Visual inspection, torque verification, thread assessment
1
Visual Inspection
Inspect the affected area for any visible signs of damage or wear
- Check for cracks or deformation
- Look for signs of excessive wear
- Verify proper fastener installation
2
Torque Verification
Verify the torque applied to the fasteners
- Check the torque wrench calibration
- Verify the torque specification
- Compare the applied torque to the specification
3
Thread Assessment
Assess the condition of the threads
- Check for signs of thread damage
- Verify the thread type and size
- Check for proper thread engagement
Prevention Guidelines
Best practices, maintenance tips, tool care
Prevention Guidelines
Best practices, maintenance tips, tool care
Best Practices
- Always follow the recommended torque specification
- Use the correct type and size of fasteners
- Verify the torque wrench calibration regularly
Maintenance Tips
- Regularly inspect the affected area for signs of wear or damage
- Replace damaged or worn-out components promptly
- Keep the work area clean and organized
Tool Care
- Regularly clean and maintain the torque wrench
- Store the torque wrench in a dry and secure location
- Verify the torque wrench calibration before each use
Frequently Asked Questions
Find answers to common questions about torque specifications
Q1 What IS the proper torque for the cylinder head bolts on a 2010 Dodge Avenger?
Q1
What IS the proper torque for the cylinder head bolts on a 2010 Dodge Avenger?
89 ft-lbs (120 Nm) + 90 degrees
Q2 What torque should I use for the oil pan drain plug on my 2008 Dodge Avenger?
Q2
What torque should I use for the oil pan drain plug on my 2008 Dodge Avenger?
18 ft-lbs (25 Nm)
Q3 What IS the recommended torque for the spark plugs in a 2014 Dodge Avenger?
Q3
What IS the recommended torque for the spark plugs in a 2014 Dodge Avenger?
15 ft-lbs (20 Nm)
Q4 What torque wrench should I use for critical bolts like the cylinder head bolts?
Q4
What torque wrench should I use for critical bolts like the cylinder head bolts?
Use a calibrated torque wrench with a range that covers the specified torque value and refer to the torque specifications provided in the service manual.
Q5 How can I prevent over-tightening bolts?
Q5
How can I prevent over-tightening bolts?
Always use a properly calibrated torque wrench, follow the torque specifications precisely, and avoid using excessive force.
Q6 What are the consequences of under-tightening bolts?
Q6
What are the consequences of under-tightening bolts?
Under-tightened bolts can lead to leaks, vibrations, and component failure.
Environmental Considerations
Temperature, humidity, and seasonal effects on torque specifications
Temperature Effects
Includes: High Heat, Cold Weather, Thermal Cycling
Temperature Effects
Includes: High Heat, Cold Weather, Thermal Cycling
Temperature can significantly impact torque values and fastener behavior
Cold Weather
Effects:
- Increased material brittleness
- Higher torque required due to thread contraction
- Reduced thread lubricant effectiveness
Recommendations:
- Allow components to warm to room temperature when possible
- Consider using winter-grade thread lubricants
- Check torque values more frequently during winter months
Hot Weather
Effects:
- Thermal expansion of components
- Decreased friction in threads
- Accelerated lubricant breakdown
Recommendations:
- Check torque when components are at normal operating temperature
- Use temperature-resistant thread lockers
- Consider re-torquing after heat cycles
Humidity and Corrosion
Covers: Rust Prevention, Salt Exposure, Moisture Control
Humidity and Corrosion
Covers: Rust Prevention, Salt Exposure, Moisture Control
Moisture and corrosion can affect fastener integrity and torque values
High Humidity
Effects:
- Accelerated corrosion formation
- Reduced friction coefficient
- Potential thread seizing
Prevention:
- Use corrosion-resistant fasteners
- Apply appropriate anti-seize compounds
- Maintain proper protective coatings
Salt Exposure
Effects:
- Rapid corrosion development
- Thread damage
- Seized fasteners
Prevention:
- Regular underbody washing
- Use of sacrificial anodes where appropriate
- Application of protective coatings
Seasonal Maintenance
Spring, Summer, Fall, and Winter maintenance schedules
Seasonal Maintenance
Spring, Summer, Fall, and Winter maintenance schedules
Spring
- Inspect for winter damage
- Clean and protect exposed fasteners
- Check torque on critical components
Summer
- Monitor heat-affected components
- Check expansion-related loosening
- Inspect cooling system mounts
Fall
- Prepare for winter conditions
- Apply corrosion protection
- Verify all fasteners are properly torqued
Winter
- More frequent inspection of critical fasteners
- Check for salt damage
- Monitor suspension component torque
Related Resources
Tools, service procedures, and technical bulletins
Recommended Tools
Digital Torque Wrench (10-100 Nm)
Essential for tightening fasteners to precise torque specifications, preventing damage and ensuring proper assembly. This range IS suitable for many applications on the Avenger.
- Digital display for accurate readings
- Audible alarm when target torque IS reached
- Multiple units (Nm, ft-lb, in-lb)
- Reversible ratcheting mechanism
Service Procedures
Tightening Wheel Lug Nuts
Follow these steps to properly tighten the lug nuts on your 2008-2014 Dodge Avenger.
- Place the chocks behind the wheels opposite to the one you're working on.
- Use the lug wrench to loosen the lug nuts, but do not remove them completely.
- Lift the vehicle using a jack and secure it with jack stands.
- Fully tighten the lug nuts using the torque wrench to 100 Nm (74 lb-ft).
- Lower the vehicle and remove the jack stands.
- Tighten the lug nuts one more time to ensure they are secure.
Replacing Spark Plugs
Here are the steps on how to replace the spark plugs on your 2008-2014 Dodge Avenger.
- Open the hood and locate the spark plugs.
- Disconnect the spark plug wires from the spark plugs.
- Use a spark plug socket to remove the spark plugs.
- Apply anti-seize to the threads of the new spark plugs.
- Hand-tighten the new spark plugs into the cylinder head.
- Tighten the spark plugs using a torque wrench to 25 Nm (18 lb-ft).
- Connect the spark plug wires to the new spark plugs.
- Start the engine and check for any leaks.
Changing Oil and Filter
Follow these steps to change the oil and filter on your 2008-2014 Dodge Avenger.
- Gather your materials: new oil filter, new oil, oil drain pan, and funnel.
- Locate the oil drain plug and place the oil drain pan under it.
- Use a wrench to loosen the oil drain plug and allow the oil to drain.
- Replace the oil drain plug and tighten it to 27 Nm (20 lb-ft).
- Locate the oil filter and use an oil filter wrench to remove it.
- Apply a thin coat of new oil to the gasket of the new oil filter.
- Hand-tighten the new oil filter onto the engine.
- Tighten the oil filter using an oil filter wrench to 18 Nm (13 lb-ft).
- Add new oil to the engine through the oil filler cap.
- Check the oil level using the dipstick.
Technical Service Bulletins
Legal Disclaimer
Important information about using this content
Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.
General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability
The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.
We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.
Technical Information
- All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
- Vehicle specifications and procedures may vary by model year, trim level, and region.
- Always follow the manufacturer's recommended procedures and safety precautions.
- Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
- If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.
About the Author
Expert automotive knowledge and experience
'/%3E%3Cpath d='M60 30a20 20 0 1 1 0 40 20 20 0 0 1 0-40zm0 45c16.5 0 30 7.5 30 16.8V100H30v-8.2c0-9.3 13.5-16.8 30-16.8z' fill='%23404040'/%3E%3C/svg%3E)
ASE
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions
Diagnostic
Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.
Repair
Expert in both traditional mechanical repairs and modern vehicle systems.
Additional Expertise
Documentation
Created over 500 detailed repair guides and technical documents.
Training
Conducted technical training sessions and contributed to repair databases.
Certifications & Research
Certifications
- ASE Master Technician Certification
- Advanced Diagnostic Specialist
- Hybrid/Electric Vehicle Systems
- Performance Tuning Expert
Research & Community
Actively researches emerging technologies and contributes to automotive forums.